WAGO 852-1305 Manual Download Page 267

Page: 267 / 314

WAGO-ETHERNET-Zubehör 852

Appendix 267

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Example

L2SWITCH

#configure terminal

L2SWITCH(config)

#bandwidth-limit egress 1 ports 1-8

L2SWITCH(config)

#bandwidth-limit ingress 1 ports 1-8

10.3.3.4 Storm Control

Table 125: CLI “Storm Control” Configuration

Node

Command

Description

enable

show storm-control

This command displays the current “Storm Control”

configurations.

configure

storm-control rate

RATE_LIMIT type (bcast

| mcast | DLF |

bcast+mcast | bcast+DLF |

mcast+DLF |

bcast+mcast+DLF) ports

PORTLISTS

This command enables the bandwidth limit for

broadcast, multicast or DLF packets and sets the

bandwidth limit of a specified type.

configure

no storm-control type

(bcast | mcast | DLF |

bcast+mcast | bcast+DLF |

mcast+DLF |

bcast+mcast+DLF) ports

PORTLISTS

This command disables the bandwidth limit for

broadcast, multicast or DLF packets.

Example

L2SWITCH

#configure terminal

L2SWITCH(config)

#storm-control rate 1 type broadcast ports 1-6

L2SWITCH(config)

#storm-control rate 1 type multicast ports 1-6

L2SWITCH(config)

#storm-control rate 1 type DLF ports 1-6

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands