manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 197

WAGO-ETHERNET-Zubehör 852  Configuring in the Web-Based Management System (WBM)  197 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

 

Manual 

 

1.1.0  

 

9.3.12  Jet Ring 

 

Figure 78: WBM “Jet Ring” Page 

Table 82: WBM “Jet Ring” Page 

Jet Ring Setting 
Parameters 

Default 

Description 

State 

Disable 

In this selection box, select “Disable” to disable the 

“Jet Ring” function on individual ports. 

Enable 

In this selection box, select “Enable” to enable the 

“Jet Ring” function on individual ports. 

Master Bridge MAC 

 

This field displays the IP address of the Jet Ring 

Master. 

Jet Ring Total Nodes 

 

This field displays the number of nodes in the Jet 

Ring. 

Bridge Role 

 

This field displays the function of the switch in the 

Jet Ring. 

Jet Ring Status 
Parameters 

Default 

Description 

Port 

1 … 10 

This column displays the port numbers. 

Port Status 

No connection 

Forwarding 

Blocking 

This column displays the port status. 

Ring Port 

Yes 

This column displays if the port operates in a ring. 

 

 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands