manualshive.com logo in svg

WAGO 852-1305, Manual

Share
Download
WAGO 852-1305 Manual Download Page 193

WAGO-ETHERNET-Zubehör 852  Configuring in the Web-Based Management System (WBM)  193 

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 

 

 

Manual 

 

1.1.0  

 

Table 79: WBM “LLDP” Page – “Settings” Tab 

LLDP Settings 
Parameters 

Default 

Description 

State 

Disable 

Select “Disable” in the selection box to disable this 

function. 

Enable 

Select “Enable” in the selection box to enable the 

LLDP function. for the switch globally. 

Tx Interval 

30 

Enter the value for the “Tx Interval” (transmission 

interval) for the LLDP packets in the input field. 

TX Hold 

4 

Enter the value for the “tx-Hold Time” in the input 

field that determines the TTL of the switch's 

message. 

(TTL = tx-hold * tx-interval) 

Time To Live 

120 

This field displays the lifetime for the switch's 

information. 

Port  

From: 

1 

Select a port or port range in the selection box for 

which you want to configure the “LLDP” setting. 

To: 

1 

Select a port or port range in the selection box for 

which you want to configure the “LLDP” setting. 

State 

Enable 

In this selection box, select “Enable” to enable the 

LLDP function on individual ports. 

Rx Only 

Select the “Rx Only” setting in the selection box if 

“Rx Interval” is always used as the transmission 

interval for the switch or ports. 

Tx Only 

Select the “Tx Only” setting in the selection box if 

“Tx Interval” is always used as the transmission 

interval for the switch or ports. 

Disable 

In this selection box, select “Disable” to disable the 

LLDP function on individual ports. 

LLDP Status 
Parameters 

Default 

Description 

Port 

1 … 10 

This column displays the port numbers. 

State 

Disable 

Enable 

This column displays if “LLDP” is enabled or 

disabled. 

 

 

 

Summary of Contents for 852-1305



























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands