WAGO 852-1305 Manual Download Page 185

Page: 185 / 314

WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 185

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

9.3.8.2 Instance Settings

Figure 71: WBM “ERPS” Page – “Instance Settings” Tab

Table 75: WBM “ERPS” Page – “Instance Settings” Tab

Instance Settings
Parameters

Default

Description

Instance

(1~30)

Enter the instance ID in the input field.

Valid range: 1 … 31

Control VLAN

Enter the VLAN of the controller for the instance in

the input field.

Valid range: 1 … 4094

Data VLAN

Enter the value for the data VLAN for the instance

in the input field.

Valid range: 1 … 4094

One or more data VLANs can be configured.

Instance Status
Parameters

Default

Description

Instance

1 … 31

This field displays the instance ID.

Control VLAN

1 … 4094

This field displays the controller VLAN of the

instance.

Data VLAN

1 … 4094

This field displays the data VLAN of the instance.

Delete

Click [Delete] to delete this setting.

Summary of Contents for 852-1305



























































































































































































































































































































Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands

WAGO 852-1305, Manual

Search results

Summary of Contents for 852-1305

Reviews:

Brands by name

Popular brands