WAGO 750-489 Manual Download Page 126

Page: 126 / 178

126 Commissioning

WAGO-I/O-SYSTEM 750

750-489 4AI RTD/TC/Strain Gauge Ex i

Manual

Version 1.1.0, valid from FW Version 02

7.1.1.2 Information Bar

• Item number: 750-489

• Item description: 4AI RTD/TC/Strain Gauge Ex i

• Version: 01.01.xx(xx)

7.1.1.3 Buttons

Table 139: Buttons

Button

Function Explanation

[Exit]

Closes the parameterization dialog.

The connection to the I/O module is interrupted.

[Open]

Opens the dialog for loading a saved parameter file.

[Save]

Opens the dialog for saving parameterization

information in a parameter file.

[Read]

Reads the current parameterization from the I/O

module.

[Write]

Writes the modified parameters to the I/O module.

[Factory

Settings]

Resets all I/O module settings to factory settings

Note

: The values for the user calibration are also reset

to their default values. Therefore, after the factory

settings are restored, modified values must be modified

again and written to the I/O module.

Tip:

Make a note of any value settings before resetting

the I/O module.

[Help]

Opens an I/O module help dialog.

Summary of Contents for 750-489



















































































































































































Search results

Summary of Contents for 750-489

Reviews:

Brands by name

Popular brands

WAGO 750-489, Manual

Search results

Summary of Contents for 750-489

Reviews:

Brands by name

Popular brands