manualshive.com logo in svg

WAGO 750-370, Manual, Page: 89 / 222

Share
Download
WAGO 750-370 Manual Download Page 89

WAGO-I/O-System 750 

Function Description 

89 

750-370 PROFINET IO Fieldbus Coupler 

 

 

Manual 

 

Version 2.0.0  

 

7.9 

Firmware Update 

The device firmware is updated via the ETHERNET interface only and has to be 

carried out using the “WAGO Ethernet Update” firmware update tool. 

A firmware update is also available via the configuration interface using the tool 

“WAGO FBC Update” possible. 

 

 

 

Firmware update tool only available on request! 

Please note that the “WAGO Ethernet Update” and “WAGO FBC Update” 

firmware update tool is only available on request. Contact Technical Support by 

e-mail at: 

[email protected].

 

 

 

The steps required to update the firmware are explained in the “WAGO Ethernet 

Update” online help or via e-mail technical support for the provision of “WAGO 

FBC Update”. 

The following requirements must be met to successfully firmware update with the 

firmware update tool “WAGO Ethernet Update”: 

•

 

The fieldbus coupler has a valid device name. 

 

The device name can be specified using a DCP service tool or via 

available DIP switch. 

•

 

The fieldbus coupler has appropriate IP settings. 

 

A DCP service tool can be used to make the IP settings or temporarily 

using the address resolution of the connected IOX. 

•

 

The IP settings remain after restarting the fieldbus coupler as part of the 

firmware update or are made available again.  

 

After the required firmware has been uploaded to the fieldbus coupler, it is 

checked for consistency and persistently stored. The firmware is applied 

by restarting via “WAGO Ethernet Update”. The tool then attempts to 

initiate extraction of the internal file system for the web server. This 

requires that the IP settings used previously are available. 

If the device name or IP settings are no longer available after restarting 

due to an only temporary assignment, they have to be reassigned to the 

fieldbus coupler using the procedures mentioned above to successfully 

complete the update process. 

Summary of Contents for 750-370































































































































































































































Reviews:

No comments