manualshive.com logo in svg

WAGO 750-370, Manual, Page: 211 / 222

Share
Download
WAGO 750-370 Manual Download Page 211

WAGO-I/O-System 750 

Appendix  211 

750-370 PROFINET IO Fieldbus Coupler 

 

 

Manual 

 

Version 2.0.0  

 

The entries for the incorrectly configured modules/submodules then follow. The 

number of existing entries is stored in the preliminary structure of the 

“ModuleDiffBlock”. 

Table 179: Structure of the Odd Modules within the Configuration 

Byte 

offset  Data type 

 

 

Description 

 

  

 

 

 

 

0 / 1 

WORD 

 

 

Slot with odd module 

 

 

 

Range   1 … 255 

2 / 3 

DWORD 

 

 

Identification of the physically plugged module 

(“ModuleIdentNumber”) 

4 / 5 

 

 

 

 

 

 

6 / 7 

WORD 

 

 

Module state 

 

 

 

0x0000  Module not plugged 

0x0001  ModuleIndentNumber wrong 

0x0002  Module is okay, but at least one submodule is 

locked, worng or missing 

0x0003  Module is not the same as requested – but the 

IO device was able to adapt by its own 

knowledge 

0x0004 

… 

0xFFFF 

Reserved 

 

 

 

 

8 / 9 

WORD 

 

 

Number of submodule slots with odd submodules, 

otherwise 0 

 

 

 

 

 

 

 

Summary of Contents for 750-370































































































































































































































Reviews:

No comments