manualshive.com logo in svg

WAGO 750-370, Manual, Page: 105 / 222

Share
Download
WAGO 750-370 Manual Download Page 105

WAGO-I/O-System 750 

Configuring via the Web-Based Management System (WBM)  105 

750-370 PROFINET IO Fieldbus Coupler 

 

 

Manual 

 

Version 2.0.0  

 

Pos:  71.4 /Serie 750 (WAGO-I/O-SYST EM)/Web-Based-Management-System  WBM/Seite Infor mation/Infor mation - Einl eitung @ 4\mod_1242221504031_21.docx @ 33104 @ 2 @ 1 

 

9.1 

Information 

The WBM page “Information” contains an overview of all important information 

about your fieldbus coupler/controller. 

Pos:  71.5 /Serie 750 (WAGO-I/O-SYST EM)/Web-Based-Management-System  WBM/Seite Infor mation/Infor mation - Bild ( 750- 370) @ 23\mod_1435236163856_21.docx @ 184584 @  @ 1 

 

 

Figure 42: WBM Page „Information“  

Pos:  71.6 /Serie 750 (WAGO-I/O-SYST EM)/Web-Based-Management-System  WBM/Seite Infor mation/Infor mation - T abell e (750-370) @ 23\mod_1435566589967_21.docx @ 184738 @  @ 1 

 

Summary of Contents for 750-370































































































































































































































Reviews:

No comments