background image

40

GA 2800EA, GA 2805EA

 

0

100

200

300

400

500

600

700

800

1 bar

2 bar

3 bar

ø 0.8

ø 1.0

ø 1.2

ø 1.4

ø 1.6

ø 1.8

ø 2.0 

B_00170

"?

"?

"?

OPERATING MANUAL

EDITION 12/2008

PART NO.  DOC350731

ACCESSORIES

9.1 

NOZZLES EA FLAT-JET

9.1.1 

PAINT OUTPUT MEASURED WITH SYNTHETIC ENAMEL

Unit:   GA 2800EAF  

Viscosity:   22 DIN 4 sec

Material pressure in bar

Output in g/min.

Part No.

Description

Colour

363228

Nozzle set EAF 0.6

black

363229

Nozzle set EAF 0.8

yellow

363230

Nozzle set EAF 1.0

red

363231

Nozzle set EAF 1.2

green

363232

Nozzle set EAF 1.4

brown

363233

Nozzle set EAF 1.6

white

363234

Nozzle set EAF 1.8

blue

363235

Nozzle set EAF 2.0

black

2303641

Air cap assy. EAF 0.6

black

353968

Air cap assy. EAF 0.8

yellow

353973

Air cap assy. EAF 1.0

red

353960

Air cap assy. EAF 1.2

green

353961

Air cap assy. EAF 1.4

brown

353962

Air cap assy. EAF 1.6

white

353963

Air cap assy. EAF 1.8

blue

353964

Air cap assy. EAF 2.0

black

2303640

Flat jet nozzle EAF 0.6

black

353969

Flat jet nozzle EAF 0.8

yellow

353970

Flat jet nozzle EAF 1.0

red

353955

Flat jet nozzle EAF 1.2

green

353956

Flat jet nozzle EAF 1.4

brown

353957

Flat jet nozzle EAF 1.6

white

353958

Flat jet nozzle EAF 1.8

blue

353959

Flat jet nozzle EAF 2.0

black

Note

: Only install EAF nozzles parts with the same colour (air cap colour and nozzle colour must be identical).

Summary of Contents for GA 2800EA





















































Reviews: