W6 N 2000 Exklusive Manual Download Page 164

Page: 164 / 220

Sewing in a zipper: Program 00

Using a Pattern

164

Manual • Sewing machine W6 N 2000 Exklusive W6 N 2000 Exklusive • 27/04/2018 • 1.0 • GBR

11.16 Sewing in a zipper: Program 00

Standard foot, Super-Stretch Needle 90 or

Use only the

00 Straight Stitch

pattern when sewing in zippers.

Select the following settings:

Settings for a zipper

Please follow the instructions below:

Prerequisite:

•

You have read the safety notes for this sewing machine, see “Safety
Notes” (page 7).

•

You have set up the machine in a safe place; see “Setting Up” (page 12).

•

You have connected the machine properly, see “Connecting the ma-
chine” (page 12).

•

Please take a look on our website www.w6-wertarbeit.com

and selct the Video "Critical for optimal threading of a

W6 N2000 Exklusive".

•

Use a W6 Super-Stretch Needle 90 (HAx 1SP) for stretch and non-
stretch fabrics, or a W6 Super-Stretch Needle 75 (HAx 1SP) for thinner
fabrics. If necessary, install a special needle.

•

You are using W6 plastic bobbins and thread tension-friendly / lint-free
W6 thread.

•

The presser foot that matches the pattern is installed.

Required:

•

A pair of scissors

CAUTION

Risk of injury posed by breaking needles

Should the sewing needle touch the teeth of the zipper while sewing, there
is a risk of injuries being caused by the needle breaking.

►

Always take care that the sewing needle does not touch the teeth of the
zipper while sewing.

Carry out the following steps:

Super-Stretch 90

Super-Stretch 75

Summary of Contents for N 2000 Exklusive





























































































































































































































Search results

Summary of Contents for N 2000 Exklusive

Reviews:

Related manuals for N 2000 Exklusive

Brands by name

Popular brands

W6 N 2000 Exklusive, Manual

Search results

Summary of Contents for N 2000 Exklusive

Reviews:

Related manuals for N 2000 Exklusive

Brands by name

Popular brands