manualshive.com logo in svg

VRmagic Eyesi, Installation And Operating Manual, Page: 23 / 80

Share
Download
VRmagic Eyesi Installation And Operating Manual Download Page 23

Connecting the simulator PC to power

Info 

Regular boot and shut down process

When connecting the simulator PC to power, the simulator PC boots up, and 
after approximately 10 seconds, shuts down again. This is a regular procedure.

1. 

Connect one end of the provided gray power supply cable to the power outlet 
located at the top of the lifting column.

2. 

Connect the other end of the gray power supply cable to the power inlet (3) of 
the simulator PC (

Â

 Fig. 5 on page 21).

4.5  Attaching the Monitor Arm

The monitor arm is delivered in a completely pre-cabled state and can be attached 
as soon as the operating table and simulator PC have been put together.

Attaching the monitor arm:

1. 

Feed all cables coming out of the bottom end of the monitor arm into the 
mounting receptacle located under the right-hand side of the operating table.

Fig. 9: Feeding the cables into the receptacle

2. 

Introduce the monitor arm into the mounting receptacle.

3. 

Push the monitor arm into the receptacle as far as it will go.

4. 

Tighten the four screws under the receptacle using the 5 mm hexagon key.

Fig. 10: Tightening the screws

23

Installation

Eyesi Surgical Simulator – Installation and Operating Guide

Summary of Contents for Eyesi

















































































Reviews:

No comments