background image

SPECIFICATIONS

Wingspan:.........................2020mm (79.5in)

Length:..............................1540mm (60.6 in)

Electric Motor:.....................See next pager

Gas Engine:....................4T 40cc / 2T 30cc

RTF Weight: 7.1Kg / 15.7lbs (Will vary with

Equipment Used).

Radio:...............8-9 Channel / 8-9 Servos

Function: Ailerons-Elevator-Rudder-Throttle

Flaps-Optional Retractable Landing Gear.

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

Radio control model / Flugmodel

ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY

U.S NAVY  

Instruction manual / Montageanleitung

TECHNISCHE DATEN

Spannweite:...................................2020mm
Lange:............................................1540mm
Elektroantrieb.............(siehe nächste Seite)
Verbrennerantrieb:..........................26-30cc
Fluggewicht:.......................................7.1Kg
Fernsteuerung......8-9 Kanal / 8-9 Servos

VQ No: VQA135

BEARCAT

Summary of Contents for U.S NAVY F.8F BEARCAT






















Reviews: