VQ Model VQA138CA Building Instructions Download Page 1

Semi scale  model

BUILDING INSTRUCTIONS / MONTAGEANLEITUNG

Specification:
Wingspan                                           72.4 in.                                        
Length                    54.1 in.(Canada version)
                                 56.5 in. (Swiss version)
Flying weight                                     7.5   lbs
Motor                                     See next pager
Radio                                     See next pager                                             

Technische Daten:
Spannweite                                      1.840mm
Länge                  1.375mm (Canada version)
                               1.435mm (Swiss version)
Fluggewicht                                          3.400g
Verbrennerantrieb 
Fernsteuerung       

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

RADIO CONTROL MODEL / RC FLUGMODELL

DHC-6

VQA138SW

VQA138CA

# C8802 Fernsteuerung GigaProp 6

# C9493 Antriebsset Brushless f.

Summary of Contents for VQA138CA

















Reviews: