Volvo SDLG LG956L Operation & Maintenance Manual Download Page 87

Page: 87 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

3.3.3 Turning

Turn the steering wheel to the desired direction. The machine will turn.

The machine takes the articulated pin at the center. And the front and rear frames turn by rotating

its waist.

△

WARNING

Never

turn suddenly or turn on a slope at high speed.

The machine can not turn if the engine stops.

3.3.4 Braking

Never

put your foot on the brake pedal unless necessary.

Never

press the brake pedal again and again unless necessary.

Never

try to stop the engine and put speed change control level in the

neutral

position while

driving down sloping ground.

Never

using left brake pedal (if assemble the double brake pedals) when driving on a slope to

prevent power from cutting off.

△

WARNING

Never

use the brake valve manual control handle (or

parking brake switch) to brake or slow the speed of the

machine while running unless in an emergency.

3.4 Stopping

3.4.1 Steps to Stop

Release the accelerator, and press the brake pedal to

stop the machine. Put the gear control lever in the

neutral

position.

After safely stopping, pull the brake valve manual

control handle up or press the parking brake switch

to lock the parking brake in the brake state.

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands