Volvo SDLG LG956L Operation & Maintenance Manual Download

Page: 83 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

The following maintenance should be done after the run-in period of new machine:

Clean the filter at the bottom of the gearbox and the oil filter cartridge of the torque converter.

Check the oil returning filter cartridge of the hydraulic oil tank.

Change the engine oil. Please refer to

3.6.1 Fuel Supplying of Engine

in this chapter.

3 OPERATION AND USE OF LOADER

3.1 Notices for Usage

The diesel must be cleaned and deposited more than 72 hours before it is to be used. The

trademark should suit the rules.

Transmission oil for the gearbox, torque converter, and the hydraulic oil for hydraulic system

must be clean.

The loader must be maintained and lubricated periodically.

Drive the loader until the brake pressure reaches 0.4MPa after the engine starts.

Put some hot water or vapor in front of the engine for preheating it. Preheat the engine until

℃

~40

℃

before starting if the environmental temperature is lower than -5 .

℃

There is no need to stop the machine or step on the brake pedal in changing the forward

levers during driving. When changing the speed from low to high, release the accelerator a

little and operate the Gear Control Lever at the same time, and step on the accelerator; when

changing the speed from high to low; release the accelerator first and then change the

transmission slowly.

After the lift-arm and bucket are moving to the required position, release the control valve

lever to the middle position.

Change the forward or backward driving direction after stopping the loader.

Full load work is allowed until the water temperature of the engine is above 60 and the

℃

mobile temperature of the engine is above 50 . But the water temperature of

℃

the engine

should not be over 95 and the mobile temperature of

℃

the engine should not be over 120 ,

℃

otherwise stop the loader to cool it.

10.

Never

lift the bucket to the highest position to transport material. The lower hinge of the lift

arm should be 400mm

～

500mm above the ground to ensure stable driving during the

transporting process.

11.

A diesel engine is used in the machine. The power of the diesel engine will go down as the

altitude, environmental temperature and relative temperature goes up. So please pay attention

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands