Volvo SDLG LG956L Operation & Maintenance Manual Download

Page: 82 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

2 RUN-IN PERIOD OF NEW MACHINE

A new machine must have a run-in period first to increase the load step by step from free rotating; so

that each part of the machine can be have full run-in period for increasing the life of the machine. It

needs 60 hours to train the new machine, and operate follows:

Run the machine in neutral at low-speed to preheat the engine.

Never accelerate the engine suddenly in the preheating period.

Never start, accelerate, turn or brake suddenly except in an emergency.

When the loader is working without a load, the gearshift should be used from low speed to high

speed at each level accordingly. Turn left, right or brake steadily in the process of driving.

In the period of run-in, all speeds including forward and reverse should be adjusted.

It is better to load bulk materials in the period of run-in. Do not operate the loader too hard or too

rudely. The load should be less than 70% of the standard load, and the speed should be better less

than 70% of the maximum speed limit.

Pay attention to the lubricating condition; routinely add and change the lubricant according to

rules.

Pay attention to the temperatures of the gearbox, torque converter, front and rear frame, rim and

brake drum. Once they are overheating, find the reason and repair it.

Check the fastening conditions of the bolts and nuts.

Do the following maintenance after 10 hours of run-in time on the new loader:

Check the fastening status of bolts and nuts of all parts, but especially the bolts of diesel engine

cylinder cover, vent-pipe bolts, front and rear frame bolts, rim bolts, transmission axle bolts and

connection bolts.

Clean the raw and essential engine oil filter and fuel filter.

Check the tension status of the belts of fan, electrical machine and air condition compressor

Check the capacity of the storage battery electrolyte and its reserves, and fasten the connect

poles.

Check the oil level of the gearbox. Please refer to

3.6.3 Adding Oil to Gearbox

in this

chapter.

Check the seal of the hydraulic system and braking system.

Check the connection and sensitivity of all control levers.

Check the temperature and the connections of the circuit system, the power supply of electrical

machine, gauge, light and lamps and turning signals.

Open the air storage tank to drain water.

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands