Volvo SDLG LG956L Operation & Maintenance Manual Download Page 53

Page: 53 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

9.2 Transportation on the Ground

Obey the rules about weight, height, width and length prescribed by national and local laws for

transporting the machine using a tow truck. Obey the traffic rules.

Know the weight, height, width and length of machine regulation before deciding the transport

routine.

Know the allowed limit of weight bearing when passing bridges or private buildings. Obey the

relative rules when driving on the public roads.

The machine may be unloaded when using other transportation. Please contact Shandong

Lingong Construction Machinery Co. Ltd. or their accredited representative.

9.3 Lifting

Use the hook of the front and rear frame to transport the

machine to ship or train.

Select proper lifting equipment according to the weight

of the loader, otherwise it is dangerous to surpass the

weight limit.

Notices for lifting:

Make sure the loader is in the transporting state.

The front and rear frame should be in the middle

position. Lock the machine using the lock bar to prevent rotation of the front and rear frame

during lifting.

All the control levers (or handles) should be in the middle position.

Stop the engine, lock all the equipment using keys and then remove.

No one is allowed to stay in the operator cab.

Never

lift the machine using steel wire connecting the two hooks on the front frame.

It is allowed to lift the machine using 4 steel wires of the same length (no shorter than 7m).

Keep the machine horizontal during lifting.

Prevent damage to hood, operator cab, and hydraulic pipes.

No person or car is allowed to pass under the machine during lifting.

Draw back the lock bar to turn the machine after lifting.

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands