Volvo SDLG LG956L Operation & Maintenance Manual Download Page 50

Page: 50 / 130

Operation & Maintenance Manual

──

LG956L Wheel Loader

8.17 Charging of Storage Battery

Explosion may occur if the storage batteries are charged in the wrong way. So follow the storage

battery instructions in this user manual. Do as follows:

Charge with constant voltage is recommended:

Complementary charge: charge 16 hours at 16.0 Voltage (max current is less than 25A)

Normal charge: charge 24 hours at 16.0 Voltage (max current is less than 25A).

Connect the positive pole of the charging machine with the negative pole of the storage battery,

and then connect the negative pole of the charging machine with the positive pole of the storage

battery. Never reverse.

Examine the vent of the battery to prevent blockage, otherwise it may explode.

Lower the charging voltage or current if the electrolytes are over 45

℃

to prevent spurt out of

electrolytes due to high temperatures.

Never

overcharge during use or charging to prevent early invalidation due to water loss, grid

increasing and diachylon dropping.

8.18 Starting to Use Voltage-Raising Method

The wrong connection of voltage-raising cable may lead to fire, so please do as follows:

Two operators are needed to start voltage-raising start (one sits on the operator seat).

Two machines are not allowed to touch when one is starting.

Turn off all the starting switches of the normal machine and the broken machine when connecting

the voltage-raising cable.

Connect the positive (

) cable first when the voltage-raising cable is connected. Cut off the

negative or ground (

) cable first when the voltage-raising cable is removed.

Connect the ground cable to the frame of the broken machine. Connection should be as far as

possible away from the storage battery.

Do not let the voltage-raising cables touch each other or let the clamp touch the machine when

the voltage-raising cable is removed.

8.19 Maintenance and Storage of Tires

8.19.1 Maintenance of Tires

The Explosion of a tire can push the parts, such as tire, rim and driving axle, as far as 500m or

Summary of Contents for SDLG LG956L



































































































































Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands

Volvo SDLG LG956L, Operation & Maintenance Manual

Search results

Summary of Contents for SDLG LG956L

Reviews:

Related manuals for SDLG LG956L

Brands by name

Popular brands