Volvo G700B Series Operator'S Manual Download Page 1

Safety when servicing

Operating instructions

Controls

Contents

OPERATOR’S MANUAL

Presentation

Instrument panels

Operating techniques

Service and maintenance

Specifications

Alphabetical index

G700B

Foreword

This Operator’s Manual is intended as a guide for the correct 
use and maintenance of the machine. Therefore, study it 
carefully before starting and operating the machine, or be-
fore carrying out any preventive maintenance.

Keep the manual in the manual box in the cab so that it is al-
ways at hand. 

Replace it immediately if it is lost.

NOTE: The manual describes the applications for which 
the machine is primarily intended, and is written to ap-
ply for all markets. We therefore ask you to disregard the 
sections that are not applicable to your machine or to 
the work for which you use your machine.

Many hours are spent on design and production to make a 
machine that is as efficient and safe as possible. The acci-
dents that occur in spite of this are mostly caused by the hu-
man factor. A safety-conscious person and a well maintained 
machine make a safe, efficient and profitable combination. 

Therefore, read the safety instructions and follow them

.

Every new Volvo Motor Grader is shipped with a

 CIMA Grad-

er

 

Safety Manual

 published by the Construction Industry 

Manufacturers’ Association. Read it carefully before operat-
ing or servicing your grader. 

We continually strive to improve our products and to make 
them more efficient through changes to their design. We re-
tain the right to make these changes without committing our-
selves to introducing these improvements on products that 
have already been delivered.

We also retain the right to change data and equipment, as 
well as instructions for service and maintenance, without pri-
or notice.

SAFETY REGULATIONS

It is the operator’s obligation to know and follow the applica-
ble national and local safety regulations. The safety instruc-
tions in this manual only apply to cases when there are no 
national or local regulations.

WARNING!

The symbol above appears at various points in the 
manual together with warning text. It means – Warning, 
be alert! Your safety is involved. It is the obligation of 
the operator to make sure that all warning decals are in 
place on the machine and that they are readable. 
Accidents may otherwise occur.
Know the capacity and limits of your machine!

This manual applies to Serial Number 35000 and up.

Ref. No.: 21 1 434 4006

Printed in Canada

Summary of Contents for G700B Series















































































































































































































































Reviews: