Volvo EPA2007 D13F Reference Manual Download Page 91 | Manualshive

Page: 91 / 179

background image

ENGINE COMPONENT AND LOCATION 85

Crankshaft

W2033313

1. Alignment Tab, Block

3. Thrust Washer

2. Alignment Tab, Cap

4. Upper and Lower Bearings

The crankshaft is drop forged steel and induction hardened. It has seven journals
with replaceable bearings. Five oversized replacement bearing options are available
to accommodate crankshaft regrinding.

The rear main cap (No. 7) includes an attaching point for the lube pump. Thrust
washers to control axial movement straddle the central journal (cap No. 4). The
remaining caps (Nos. 1–3, 5 and 6) are numbered to facilitate correct assembly.

A Teflon® seal bearing directly on the crankshaft flange is used at the front of the
crankshaft. The front seal has an outer felt ring which serves as a dust cover. At the
rear of the crankshaft is another seal that bears directly on the machined surface of the
crankshaft gear. Additionally at the rear, there is a groove in the rear crankshaft flange
for an O-ring which forms a seal between the flange and the gear.

«
...
89
90
91
92
93
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

Brand: Kubota Pages: 138

Brand: DAF Pages: 87

Brand: WÄRTSILÄ Pages: 522

Brand: Weber Pages: 35

Brand: Mercury Pages: 878

Brand: Lister Petter Pages: 81

Brand: Lister Petter Pages: 100

Para-RC Cloud 0.5 ARF

Brand: Hacker Pages: 6

Brand: Hacker Pages: 8

Brand: Hacker Pages: 8

Brand: Yanmar Pages: 94

Brand: Honda Pages: 431

Brand: Roto Pages: 8

Brand: Wood-mizer Pages: 18

Brand: LinMot Pages: 41

P01-37S-HP-SSCP

Brand: LinMot Pages: 28

Brand: Sauer Danfoss Pages: 16

Brand: JAC Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands