Volvo EPA2007 D13F Reference Manual Download Page 53 | Manualshive

Page: 53 / 179

background image

SPECIFICATIONS 47

Engine Component Torque Specifications (Critical
Fasteners)

Note:

All components are to be clean and free from foreign material or corrosion.

Assemblies are to be made using suitable tools and procedures so that no permanent
damage will occur as a result of the assembly.
Threads, washers, under head of screws and washer face of nuts should be lubricated
with clean engine oil unless otherwise specified.
The following listed fasteners require the use of a calibrated manual torque wrench. If
an adapter is required in combination with a torque wrench, a correction factor must be
applied to the torque wrench reading in order to obtain accurate fastener torque values.
Fasteners noted by an asterisk (*) require retorque after engine run-in.

Fastener Reuse

CAUTION

Repeated tightening of fasteners and threaded components reduces their capacity
to function adequately. The following table describes the various items and the
limits of their reusability. Failue to conform to these limits may result in severe
component damage.

Fastener Reuse

Fssteners

Example

Reusable
Limit

Reusable Recommendation

Highly
loaded screws
(Phosphating plus
oil)

Cylinder
Head
Injector
yoke
Camshaft
Bearing
Housing
Transmission
Flywheel

5 times

Apply engine oil on threads and
under screw heads.
Mark bolt head with an indentation.
Dry mounting for new screws
(delivered with oil pre-applied and
anti-rust treatment for spare parts).
If a part is replaced, e.g., cylinder
head, also replace the screws.

Highly
loaded screws
(Phosphating plus
oil)

Connect-
ing rods
for D13F
engines

5 times

Apply Molykote grease
“G-Rapid+MoS2” (spray).

Special screws
(specific shape)

Oil pan
and valve
cover

No limit

No limit if no cracks, corrosion or
damage to the flat surface.

«
...
51
52
53
54
55
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

Brand: Wartsila Pages: 168

Brand: MAK Pages: 2027

Brand: Saito Pages: 2

Brand: Kohler Pages: 44

MTR-DCI-...IO Series

Brand: Festo Pages: 182

Brand: ZAFFER Pages: 28

Brand: Brother Pages: 76

Brand: Brother Pages: 112

Brand: Brother Pages: 22

ZAtop SM180.24/B

Brand: ZIEHL-ABEGG Pages: 16

Brand: Robin Pages: 63

Brand: DUROMAX Pages: 32

EASY-KART 100cc

Brand: IAME Pages: 35

Brand: SSANGYONG Pages: 14

Brand: Yanmar Pages: 275

Metaphaser MP-LE1007

Brand: Metaphase Technologies Pages: 35

Brand: Tahmazo Pages: 3

Brand: Honda Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands