Volvo Penta TAD570VE Operator'S Manual Download Page 85

Page: 85 / 96

Lubrication System

Oil capacity including oil filters, approx.:

TAD570–72VE

16 liters (4.23 US gal)

TAD870–73VE

27 liters (7.13 US gal)

Oil Sump

TAD570–72VE
Min
Max

10 liters (2.51 US gal)
14 liters (3.57 US gal)

TAD870–73VE
Min
Max

19 liters (5.02 US gal)
24 liters (6.36 US gal)

Oil pressure

At rated engine rpm

TAD570–72VE

430 kPa (62 psi)

TAD870–73VE

425 kPa (62 psi)

Oil filter

Full flow filter

Lube oil pump

Type

Gear driven

Oil recommendations

Oil quality

Service interval, reached first in operation

VDS-4.5 (15W-40)

500

hours or 12 months

VDS = Volvo Drain Specification

Viscosity

Select the viscosity according to the table.

The temperature values refer to stable ambient
temperatures.

* SAE 5W/30 refers to synthetic or semi-synthetic oils.

Technical Data

47711083 09-2018 © AB VOLVO PENTA

Summary of Contents for TAD570VE

































































































Search results

Summary of Contents for TAD570VE

Reviews:

Related manuals for TAD570VE

Brands by name

Popular brands

Volvo Penta TAD570VE, Operator'S Manual

Search results

Summary of Contents for TAD570VE

Reviews:

Related manuals for TAD570VE

Brands by name

Popular brands