manualshive.com logo in svg

Volvo Penta TAD570VE, Operator'S Manual

Share
Download
Volvo Penta TAD570VE Operator'S Manual Download Page 64

Fuel Filter, Replace

IMPORTANT:

Risk of material damage.
The wrong type of fuel filter may damage the fuel
injection circuit.
Use only a fuel filter approved by the manufacturer.

IMPORTANT:

Take great care to keep fuel system unions clean.
Even minimal amounts of dirt can cause engine
breakdown.

Removal

1 Clean around the filter cover and housing.

2 Carefully remove the fuel filter cover and filter.

NOTICE!

 Be prepared to gather up fluid. The filter

is still full of fuel and there is a risk of spillage when
the cover is removed.

3 Remove the O-ring and filter.

Let the fuel drip off into a collection vessel.

Installation

1 If the new filter housing is completely empty,

lubricate with diesel around the inner section of the
filter sealing surface.

2 Lubricate the O-ring with diesel before installing the

filter cover.

3 Install the filter in the filter cover. Make sure the filter

seats properly in the cover.

4 Install the filter cover and filter in the bracket.

Carefully screw in the cover and check that the O-
ring does not get twisted. Re-lubricate the seal as
necessary.
Tighten the cover to: 25 Nm (18.4 lbf. ft.)

5 Bleed the fuel system according to 

Fuel Pre-filter,

Bleeding, page 64

.

6 Start and warm up the engine. Check that no

leakage occurs.

 

Maintenance

62

47711083 09-2018 © AB VOLVO PENTA

Summary of Contents for TAD570VE

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands