Volvo Penta TAD1340VE Operator'S Manual Download

Page: 38 / 106

CIU (Control Interface Unit)

TAD1640VE-B, TAD1641GE-B, TAD1641VE-B,
TAD1642GE-B, TAD1642VE-B, TAD1643VE,
TAD1650GE, TAD1650VE, TAD1651GE,
TWD1643GE, TWD1652GE, TWD1653GE

The CIU is a "translator" between the control unit
(EMS) and the customer's own control panel. The CIU
has two serial communication links, one fast and one
slow.

The fast one is a so-called CAN link. All data related to
instruments, indication lamps, connectors and
potentiometers is controlled by this link.

The slow link manages diagnostic information for
flashing codes etc.

Easy Link Instruments

The following Easy Link instruments are available:

- Tachometer / hours counter (fault codes are also

displayed on the tachometer display when the
diagnostic button is pressed)

- Coolant temperature

- Oil pressure

- Oil temperature

- Battery voltage

- Alarm panel

- Turbo pressure

P0002060

Instruments and Controls

47711296 01-2019 © AB VOLVO PENTA

Summary of Contents for TAD1340VE











































































































Search results

Summary of Contents for TAD1340VE

Reviews:

Related manuals for TAD1340VE

Brands by name

Popular brands

Volvo Penta TAD1340VE, Operator'S Manual

Search results

Summary of Contents for TAD1340VE

Reviews:

Related manuals for TAD1340VE

Brands by name

Popular brands