background image

Operator’s Manual

Medium-Duty Electric Slicers

©

2016 The Vollrath Company L.L.C.

Part No. 350008-1 en

4/28/16

Please register your product at Vollrath.com

Thank you for purchasing this Vollrath equipment. Before operating the
equipment, read and familiarize yourself with the following operating
and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. Save the original box and packaging. Use this packaging
to ship the equipment if repairs are needed.

SAFETY PRECAUTIONS

To ensure safe operation, read the following statements and understand
their meaning. This manual contains safety precautions which are
explained below. Please read carefully.

Warning is used to indicate the presence of a hazard that will or can
cause severe personal injury or death.

Caution is used to indicate the presence of a hazard that will or can
cause minor or major personal injury if the caution is ignored.

NOTICE: Notice is used to note information that is important but not

hazard-related.

To reduce risk of injury or damage to the equipment:

• Keep out of reach of children.
• Do not turn equipment on unless all guards are in place.
• Do not feed food by hand; always use the food pusher.
• Equipment must be connected to a properly grounded electrical

supply matching the nameplate rating.

• Always unplug equipment before cleaning.
• Keep equipment away from water; avoid water jets during cleaning.
• Equipment should only be used in a flat, level position.
• Do not operate unattended.
• Install or locate this equipment only in accordance with the provided

installation instructions.

• Keep equipment and power cord away from open flames, electric

burners or excessive heat.

• Do not operate this equipment if it has a damaged cord or a plug, if it

is not working properly or if it has been damaged or dropped.

• Do not immerse the cord or plug in water. Do not let the cord hang

over the edge of a table or counter.

• Do not use an extension cord with this equipment. Do not plug this

equipment into a power strip or multi-outlet power cord.

• Have qualified personnel install this equipment in accordance with

local codes and ordinances.

• Do not spray controls or outside of equipment with liquids or

cleaning agents.

• Do not clean the equipment with steel wool.

40950

40951

Item No. Model No. Description

Drive Peak HP Voltage Amps

Plug

40950

SLM250/S

10

"

Blade

Belt

1/3

120

2.5

NEMA
5-15P

40951

SLM300P/S 12

"

Blade

2/5

1.8

WARNING

CAUTION

WARNING

Severe injury can occur if this equipment is not used properly.

Summary of Contents for SLM250/S









Reviews: