Voith 9 186826 0 Installation And Operating Manual Download Page 20

 

Installation and Operating Manual 

 

I/H Converter DSG-B03212 

DSG-B07212

 

 

 

 

 

 

2019 / 02 

 

J.M. Voith SE & Co. 

KG │ Division Digital Ventures 

Page: 20 / 22 

918 3626018861 en 

D – 74564 Crailsheim 

Version: 4.1 

 

8.2 

Inspections 

Inspection intervals 

Inspection work 

Within the scope of the regular 
plant inspection 

Check I/H converter, pipes, pipe unions and connections on the I/H 
converter for leaks, impurities and damage. 

Remedy any leaks, impurities and damages detected , as required, during 
appropriate operating phases. 

Monitor the I/H converter operating behavior for any changes (e.g. noise). 
Eliminate the causes, as required, during appropriate operating phases. 

Inspection works after 60,000 
operating hours, 7 years after first 
commissioning at the latest 

Remove the I/H converter from the machinery and disassemble same in 
an appropriate workshop. Inspect the inner parts and replace 
conspicuous parts. Replace all seals. 

Perform a test run on a suitable test stand; check and document the I/H 
converter operational behavior. 

Inspection works after another 
60,000 operating hours, 7 years 
after the last inspection at the 
latest 

Remove the I/H converter from the machinery and have it inspected and 
completely overhauled at 

J.M. Voith SE & Co. KG │ Division Digital 

Ventures, Crailsheim. All the conspicuous parts will be replaced. By 
performing a test run, the operating behavior will be checked and 
documented. 

8.3 

Spare parts information 

 

  It is only allowed to install original Voith parts. 

  The manufacturer only is able to guarantee an expert repair and/or maintenance. 

 

 

  These inspection works can be performed by the operator's expert personnel, provided 

they meet the relevant criteria stated in Chapter 2.3. 

 

  These inspection works must only be performed by the operator's trained expert 

personnel in an appropriate workshop or by Voith personnel at the Voith workshop. 
(See Section 2.3.) 

 

  Only 

J.M.  Voith  SE  &  Co.  KG  │  Division  Digital  Ventures  expert  personnel are 

exclusively allowed to perform these inspection works. Removal of the I/H converter is 
performed by the operator's expert personnel according to Chapter 2.3. 

 

 

  For deliverable spare parts, please refer to the spare parts catalog of the outline 

drawing (see Chapter 10). In case that required parts are not included, please contact 

 

J.M. Voith SE & Co. KG │ Division Digital Ventures, Crailsheim. 

  Storage of spare parts is only allowed if these are protected against corrosion. The 

storage area has to be dry and free from dust. Prior to installing the parts, remove the 
corrosion protection. 

  Do not store the elastomere seals together with chemicals, solvents, fuels, acids, etc. 

They need to be packed airtight and protected against light with a high content of UV 
rays. The storage time until the I/H converter gets used must not exceed 6 years (for 
NBR) and 10 years (for FPM). 

Summary of Contents for 9 186826 0























Reviews: