Voce PR14037000 Page 23 Operator'S Manual Download

Page: 23 / 68

Secti

–

Clean

g and

fil

lin

g P

cedu

4.5.9 Cup Check

Check the levels of the cups in the cup turret and where necessary, refill with correct sized cups.

Allow the cups to drop into the tubes directly from the packaging. DO NOT touch the cups with
your hands.

Important:

Do not fill the tube directly above the cup dispense position. Allow the cup turret

motor to rotate a full tube to the cup dispense position when the machine is powered up.
Rotating the cup turret by hand will damage the mechanism.

Note:

If paper cups are being loaded, each pack of cups must first be inspected for damage to

the cup rims. Damaged cups must not be used.

4.5.10 Cash Box

Un-lock the cashbox (if fitted) located on the rear of the door and remove from the machine.
Empty contents from the cashbox. Refit the cashbox to the machine, turning the lock to secure.

Check the coin tubes and refill if required.

4.5.11 Test

Using the service keypad located in the rear of the door, proceed as follows:

Press the

Cup Test

button

(7)

and check that a cup is

ejected correctly from the Cup drop unit.

Press the

Park Head

button

(8)

to ensure that the

dispense head operates correctly and that the dispense
pipes are fitted correctly.

Place a suitable container under the dispense head and press the

Rinse/Flush

button

(3)

. The machine will flush the system. Check that none of the mixing stations leak.

Empty the contents of the container.

Place an empty cup under the dispense head. Press the

Test Vend

button

(6)

and

using the selection buttons on the front of the machine, vend a drink to ensure that
the machine operates correctly.

Press the

“X”

(Exit) key to exit from the Test Vend menu.

Press the View Counters button

(5)

and record the audit information displayed on the

LCD (

see sub-section 5.5 Button 5 - View Counters for full details

4.6 Oltre Brewer Cleaning Procedure

4.6.1 Daily Cleaning Procedure

Important:

It is necessary to carry out the cleaning and maintenance procedure outlined on the

following pages on a regular basis, either at the end of the day or at the start of the day before
the machine is in constant use.

Summary of Contents for PR14037000





































































Search results

Summary of Contents for PR14037000

Reviews:

Related manuals for PR14037000

Brands by name

Popular brands

Voce PR14037000, Operator'S Manual

Search results

Summary of Contents for PR14037000

Reviews:

Related manuals for PR14037000

Brands by name

Popular brands