background image

 

 

VXO8330B/5901B 

INSTALLATION GUIDE

 
 

 

PAGE 1 of 6

 

BEFORE BEGINNING YOUR INSTALLATION 

Read through the instruction guide before getting started with the installation. Professional installation is recommended for 
this product. 
 

 

 

CONTENTS 

Quintuple Trumpet Train Air Horn (Black) 

1/2" NPT Male to Two 1/2" NPT Female Tee x 2 

200 PSI Air Compressor (Black) 

1/2" NPT Female Cross x 1 

3 Gallon Air Tank 

1/4" NPT Male for 3/8" OD Hose PTC Fitting x 5 

12V 1/2" NPT High Flow Electric Solenoid 

1/2" NPT Male for 3/8" OD Hose PTC Fitting x 5 

240 PSI Air Pressure Gauge 

1/2" NPT Male for 1/2" OD Hose PTC Fitting x 1 

120-150 PSI Pressure Switch 

1/2" NPT Male to 1/2" NPT Male Coupling x 1 

250 PSI Safety Valve 

1/4" OD Nylon Plastic Hose (6 Feet) 

1/4" NPT Wing Style Drain Valve 

1/2" OD Nylon Plastic Hose (50 Feet) 

1/4" NPT Compression Fitting for 1/4" OD Air Line 

3/8" OD Nylon Plastic Hose (50 Feet) 

1/4" NPT Hex Head Male Plug 

Air Hose Cutter 

1/2" NPT Hex Head Male Plug 

Thread Sealant 10ml 

30A In-line Fuse with Waterproof Holder 

12mm Thread Sealant Tape (16 Feet) 

Remote Mount Air Filter 

Horn Button 

Mounting Hardware 

 

 

 

 

SAFETY INSTRUCTIONS 

  Do not attempt to disassemble, repair or customize this product. 

  Avoid setting up any parts of this product where there is a risk of falling off or risk of coming in contact with water. 

  Avoid reaching out to touch or pick up any fallen or water submerged parts. 

  Never leave this product unattended during use. 

  Intended for use by adults only. 

  During and immediately after use, avoid touching any part of the compressor with bare hands as it is very hot 

during such periods. 

  Avoid sounding the air horn when in close range to your ear(s) or the ear(s) of others. 

  Avoid use of product near flames, explosive materials, aerosol products or oxygen devices. 

  Be sure to pump nothing other than atmospheric air. 

  It is important to determine the maximum air pressure for any tool or attachment before using it. 

  Air sprayer or nozzle should always be pointed away from any part of the body. 

The specific voltage requirement for this horn system is 12 volt DC, therefore installation must be done to a DC 
power source of 12 volts. 

Summary of Contents for VXO8330B/5901B







Reviews: