Vivotek VS8100-v2 User Manual Download

Page: 47 / 312

VIVOTEK

User's Manual - 47

Media > Video

Stream settings

Click the stream item to display the detailed information. The maximum frame size will follow your

settings in the above Viewing Window sections.

This Network Camera offers real-time H.264 and MJPEG compression standards for real-time

viewing. If the

H.264

mode is selected, the video is streamed via RTSP protocol. There are several

parameters through which you can adjust the video performance:

■ Frame size

You can set up different video resolutions for different viewing devices. For example, configure

a smaller frame size and lower bit rate for remote viewing on mobile phones and a larger video

size and a higher bit rate for live viewing on web browsers, or recording the stream to an NVR.

Note that a larger frame size takes up more bandwidth.

Summary of Contents for VS8100-v2

























































































































































































































































































































Search results

Summary of Contents for VS8100-v2

Reviews:

Related manuals for VS8100-v2

Brands by name

Popular brands

Vivotek VS8100-v2, User Manual

Search results

Summary of Contents for VS8100-v2

Reviews:

Related manuals for VS8100-v2

Brands by name

Popular brands