manualshive.com logo in svg

Vivotek AW-IHT-1270, User Manual

Share
Download
Vivotek AW-IHT-1270 User Manual Download Page 133

 

125 

 

6.11.1.3.

 

Web Configuration 

 

 

 

Parameter 

Description 

PoE Mode 

Selects the PoE mode, classification or consumption. 

Classification

 - Allocated power according to class (0 to 4). 

Consumption 

- Allocated power according to the actual need of each 

PD. 

Port 

Selects  a  port  or  a  range  of  ports  that  you  want  to  configure  the  PoE 
function.

 

State 

Selects 

Enable 

to enable the PoE function on the specific port. 

Selects 

Disable 

to disable the PoE function on the specific port. 

Priority 

Selects 

Critical / High / Low 

priority for the specific port. 

Apply 

Click 

Apply 

to take effect the settings. 

Refresh 

Click 

Refresh 

to begin configuring this screen afresh. 

PoE Mode 

Displays the current PoE mode. 

Summary of Contents for AW-IHT-1270





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands