Vivitek DK10000Z Page 15 User Manual Download | Manualshive

Page: 15 / 62

background image

DK10000Z Series DLP Projector - User Manual

UM100000823EN03

15

Installation and Setting up

Inserting or Changing the Remote Control Batteries

1

2

3

1.  Remove the battery compartment cover by sliding the cover in the direction of the arrow.
2.  Place two AA batteries with the correct polarity.
3.  Slide on the cover as the arrow in the illustration.

Important

•

Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can

disrupt remote control operation.

•

Be sure nothing obstructs the path between the remote control and the projector.

•

Do not expose the remote control to high temperature or humidity; otherwise, the remote control will not work

functionally.

Battery installation instructions

•

Make sure the battery is installed with the correct polarity.

•

Do not use the old and new batteries or the batteries of different types together

•

Remove the battery if the remote control may not be used for a long time to prevent the damage caused by

leaks.

«
...
13
14
15
16
17
...
»

Summary of Contents for DK10000Z































































Reviews:

No comments

Related manuals for DK10000Z

Brand: Barco Pages: 106

Brand: Avio Pages: 3

Brand: Optoma Pages: 57

Brand: Leonics Pages: 21

Brand: Navitar Pages: 2

Brand: ACCO Brands Pages: 31

isobar HT1210ISOCTR

Brand: Tripp Lite Pages: 4

Brand: Epson Pages: 36

Brand: Epson Pages: 8

Brand: Epson Pages: 12

Brand: Epson Pages: 6

Brand: Epson Pages: 2

Brand: Epson Pages: 2

Brand: Epson Pages: 2

Brand: Epson Pages: 2

Brand: Epson Pages: 2

Brand: Epson Pages: 2

Brand: Epson Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands