manualshive.com logo in svg

Vivato VA4200, User Manual, Page: 159 / 181

Share
Download
Vivato VA4200 User Manual Download Page 159

159

Copyright © 2004-2005, Vivato, Inc.

Broadcast Address

See 

IP Address

.

BSS

A 

basic service set

 (BSS) is an 

Infrastructure Mode

 

Wireless Networking Framework

 with a single AP/

Bridge. Also see extended service set (

ESS

) and independent basic service set (

IBSS

).

BSSID

In 

Infrastructure Mode

, the 

Basic Service Set Identifier

 (BSSID) is the 48-bit 

MAC

 address of the wireless 

interface of the 

AP/Bridge

.

CCMP

Counter mode/CBC-MAC Protocol

 (CCMP) is an encryption method for 

802.11i

 that uses 

AES

. It employs 

a 

CCM

 mode of operation, combining the Cipher Block Chaining Counter mode (CBC-CTR) and the 

Cipher Block Chaining Message Authentication Code (CBC-MAC) for encryption and message integrity.

AES-CCMP requires a hardware coprocessor to operate.

CGI

The 

Common Gateway Interface

 (CGI) is a standard for running external programs from an 

HTTP

 server. It 

specifies how to pass arguments to the executing program as part of the 

HTTP

 request. It may also define 

a set of environment variables. 

A CGI program is a common way for an 

HTTP

 server to interact dynamically with users. For example, an 

HTML page containing a form can use a CGI program to process the form data after it is submitted. 

Channel

The 

Channel

 defines the portion of the radio spectrum the radio uses for transmitting and receiving. Each 

802.11

 standard offers a number of channels, dependent on how the spectrum is licensed by national and 

transnational authorities such as the

 Federal Communications Commission (FCC)

, the 

European 

Telecommunications Standards Institute (ETSI)

, the 

Korean Communications Commission

, or the 

Telecom Engineering Center (TELEC)

.

Client

A wireless 

client

 is any device that is equipped with an IEEE 802.11a, 802.11b, or 802.11g wireless 

interface that uses radio signals to connect to an 802.11 access point or base station in order to access 
hosts on a local network or a gateway that provides access to the Internet. Common examples of clients 
are laptop computers, personnel digital assistants (PDAs), and remote video cameras. Clients are also 
referred to as "

stations

". 

CSMA/CA

Carrier Sense Multiple Access with Collision Avoidance

 (CSMA/CA) is a low-level network arbitration/

contention protocol. A station listens to the media and attempts to transmit a packet when the channel is 
quiet. When it detects that the channel is idle, the station transmits the packet. If it detects that the channel 
is busy, the station waits a random amount of time and then attempts to access the media again.

CSMA/CA is the basis of the IEEE 802.11e Distributed Control Function (

DCF

). See also 

RTS

 and 

CTS

.

Summary of Contents for VA4200






















































































































































































Reviews:

No comments