background image

Use, Cleaning and Maintenance

1-  Deformations and failures on the surface, electronic parts due to practices other than the use functions specified in the User 

Guide,

2-  Deformations and dullness occurring on the surface of products wiped with cleaning substances containing acid and cleaning 

substances containing abrasive powders,

3-  Deformations and dullness occurring on the surface of products wiped with rough cleaning substances (wire sponge, hardened 

sponge, etc.),

4-  Pattern degradation due to the patterned glasses of the cabins being cleaned by a cleaning agent other than water.
5-  Deformations that welding electrode sparks, flammable substances during alterations made in the bathroom spaces and 

cigarettes may cause on the product surface,

6-  Failures occurring due to use of parts other than original spare parts,
shall be treated out of scope of the warranty.

Shipping, Storage

1-  Deformations to the product surface during the shipping and transportation carried out after the products are delivered or any 

breakages which may occur as the result of impacts,

2-  Deformations and breakages on the surfaces of products which remain at the construction site for a long time without 

protection,

3-  Damage to the product as the result of effects of the water and/or humidity in the environment during the storage and use of the 

products,

4-  Products damaged by each other due to stacking on top of each other during storage, 
shall be treated out of scope of the warranty.

Installation

1-  Failures which occur as the result of incorrect installation, maintenance, repairs and disassembly performed by unauthorized 

persons,

2-  Factors which impact the installation of the product, resulting from hot-cold water, waste water outlet installments which do not 

comply with the standard infrastructure specifications provided in the Technical Data Sheets, or the wall or floor not being level,

3-  Surface deformations and failures occurring due to small particles in the plumbing (stone, sand, gravel, etc.) and encrustation,
shall be treated out of scope of the warranty.

DEFECTS NOT COVERED UNDER WARRANTY

Eczacıbașı Yapı Gereçleri San. Ve Tic. A.Ș.

Reserves the right to make any technical changes on the product without prior notice

S-5900232
K-5900232

Summary of Contents for ACRYLIC SHOWER TRAYS













Reviews: