background image

VITEK

VITEK

VTC-TNB4RMA4 

Transcendent Series 4 MegaPixel 

Gen. IV  Advanced A.I.  

Motorized IP Bullet Camera 

QUICK START GUIDE

FEATURES:

• 1/3” 4.0 Megapixel CMOS Image Sensor

• NDAA Compliant

• Up to 30fps live view @ 4 MegaPixel (2592x1520)

• 2.8~12mm Motorized Varifocal Lens

• Matrix IR (up to 165’ IR Range)

• True Wide Dynamic Range

• True Mechanical Day/Night function by ICR

• XD-DNR (3D & 2D-DNR) Noise Reduction 

• Gen. IV Advanced Analytics: Regional Entrance / Exit Detection, Line 

Crossing, Target Counting [All by Human / Motor Vehicle Classification] 

Face Detection, Object Abandoned / Missing,  Heat Map, Video Blur, Video 

Color Cast Detection,  Abnormal Video

• H.265+/H.265/H.264+/H.264/MJPEG

• 1 Ch. Audio In*

• Remote Viewing via CMS, Internet Explorer, iOS & Android Apps

• ONVIF Compliant

• MicroSD Card Slot for Local Recording (256GB)

• IP67 Weather Resistance

• Wall Mount Included & Junction Boxes (VT-TJB08) Available  

(see pg. 9 for additional mounting options)

• 12VDC & PoE (Power over Ethernet) Operation

*Please research local, state and federal laws regarding the implementation of audio surveillance.

PLEASE NOTE: 

Complete User Guide, Software, Tools, and Updates are 

available online.  Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

Also Available in Charcoal,  

VTC-TNB4RMA4B

Summary of Contents for VTC-TNB4RMA4













Reviews: