D-302914
1
MCT-212 GS
GB/US: LED indicator
SP: Indicador LED
PT: Indicador LED
GB/US: Fastener
SP: Seguro
PT: Segurança
GB/US: Transmit
Button
SP: Botón de
transmission
PT: Botão de
Transmissão
GB/US: Loop
SP: Hebilla
PT: Presilha
MCT-212 GS with Wrist Band /
AMBER con Pulsera para Muñeca /
AMBER com faixa para o pulso
GB/US: Safety release mechanism
SP: Mecanismo de liberación de seguridad
PT: Mecanismo de liberação da segurança
GB/US: Neck cord
SP: Colgante para el cuello
PT: Cordão para o pescoço
GB/US: Fastener
SP: Seguro
PT: Segurança
MCT-212 GS with Neck Strap / con correa para el
cuello / AMBER com cinta para o pescoço
English
Waterproof
PowerCode Wrist
Transm
uide
itter – User
G
Español
Transmisor
Impermeable de
Pulsera PowerCod
Guía de Usuario
e
-
Portuguese
Transmissor
Impermeável de
Pulso Acionado a
Código – Guia do
Usuário
ENGLISH (GB/US)
1. INTRODUCTION
The MCT-212 GS is a miniature waterproof transmitter,
designed for home health care signaling. In the event of an
emergency, help can be summoned at the press of the
C.
ainst faults.
cy
inations.
tteries according to the manufacturer's
ort to the
transmitter button.
All MCT-212 GS units are supplied with a wrist band and neck
strap. They can be worn on the wrist or around the neck.
The LED lights during a transmission to indicate a good battery.
If the LED flashes during a transmission, this means that the
battery is low and must be replaced immediately. Anytime the
MCT-212 GS is pressed when the battery is low, a trouble signal
will automatically be sent to the Base Unit.
To alert you of the trouble, a red LED will flash and a trouble
message will appear on the display of the Base Unit. All troubles
are reported to the Monitoring Center.
The transmitter case is waterproof, hermetically sealed (no
screws) and therefore disposable. Do not attempt to open the
transmitter case or replace the battery; such action will void the
warranty.
ENROLLMENT
2.
TEST, MAINTENANCE &
2.1 Enrolling Transmitters
In order for a transmitter to function, its ID must be enrolled
into the Base Unit. The Transmitter ID is a 6 character code
(ex: EB1772) that can be found both on the unit’s package
and on the reverse side of the unit. To enroll a transmitter,
provide central station (either by telephone or by fax) of the
Transmitter ID.
2.2 Initial Test
Upon pressing the transmit button, the Base Unit will sound
and display simultaneously a message of calling for help.
This indicates that the transmitter is working properly.
Note: If for any reason the MCT-212 GS
does not result in the
above response from the Base Unit, please contact the
central station and verify the Transmitter ID located both on
the unit's package and on the reverse side of the transmitter
beneath the wrist band
.
NTS
3. GENERAL COMME
Product Limitations
Our wireless systems are very reliable and are tested to high
standards. However, due to their low transmitting power
(required by FCC, DTI and other regulatory authorities) there
are some limitations to be considered:
A.
Receivers may be blocked by radio signals occurring on or
near their operating frequencies, regardless of the code
selected.
B.
A receiver can only respond to one transmitted signal at a
time.
Wireless equipment should be tested regularly (at least
there are sources of
once a week) to determine if
interference and to protect ag
4. SPECIFICATIONS
Frequency (MHz):
315, 433.92, 868 or other frequen
according to local requirements.
Transmitter ID:
Over 16 million possible code comb
Transmit Duration:
Up to 5 sec
Power Supply:
3-volt Lithium cell type CR-2032
Battery Life Expectancy:
6 years (for typical use)
Caution!
Risk of explosion if battery is replaced by an incorrect
type. Dispose of used ba
instructions.
Battery Supervision:
Good battery - LED lights steadily upon activation.
Low battery - LED flashes upon activation.
Note: If transmission is still possible despite the battery
condition, the MCT-212 GS
will send a low battery rep
receiver.
re:
0° to 50°C (32° to 122°F).
Operating Temperatu
39 x 37 x 13 mm (1-9/16 x 1-7/16 x 5/8 in.).
Dimensions:
Weight:
25 g (0.9 oz).
Color:
Gray
This device complies with Part 15 of the FCC Rules and RSS-
210 of Industry and Science Canada. Operation is subject to
the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
The digital circuit of this device has been tested and found to
comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in
residential installations. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio and television reception. However, there
is no guarantee that interference will not occur in a particular