D-300570
1
MCT-212 AMBER
English
Waterproof
PowerCode Wrist
Transmitter – User
Guide
Español
Transmisor
Impermeable de
Pulsera PowerCode
- Guía de Usuario
Portuguese
Transmissor
Impermeável de
Pulso Acionado a
Código – Guia do
Usuário
GB/US: LED indicator
SP: Indicador LED
PT: Indicador LED
GB/US: Fastener
SP: Seguro
PT: Segurança
GB/US: Transmit
Button
SP: Botón de
transmission
PT: Botão de
Transmissão
GB/US: Loop
SP: Hebilla
PT: Presilha
MCT-212 AMBER with Wrist Band /
AMBER con Pulsera para Muñeca /
AMBER com faixa para o pulso
GB/US: Safety release mechanism
SP: Mecanismo de liberación de seguridad
PT: Mecanismo de liberação da segurança
GB/US: Neck cord
SP: Colgante para el cuello
PT: Cordão para o pescoço
GB/US: Fastener
SP: Seguro
PT: Segurança
MCT-212 AMBER with Neck Strap / con correa para el
cuello / AMBER com cinta para o pescoço
ENGLISH (GB/US)
1. INTRODUCTION
The MCT-212 AMBER is a miniature waterproof transmitter,
designed for home health care signaling. In the event of an
emergency, help can be summoned at the press of the
transmitter button.
All MCT-212 AMBER units are supplied with a wrist band and
neck strap. They can be worn on the wrist or around the
neck.
The LED lights during a transmission to indicate a good battery.
If the LED flashes during a transmission, this means that the
battery is low and must be replaced immediately. Anytime the
MCT-212 AMBER is pressed when the battery is low, a trouble
signal will automatically be sent to the Base Unit.
To alert you of the trouble, a red LED will flash and a trouble
message will appear on the display of the Base Unit. All troubles
are reported to the Monitoring Center.
The transmitter case is hermetically sealed (no screws) to
ensure complete waterproofing of the case. Therefore battery
replacement must be performed by the factory only.
2.
TEST, MAINTENANCE & ENROLLMENT
2.1 Enrolling Transmitters
In order for a transmitter to function, its ID must be enrolled
into the Base Unit. The Transmitter ID is a 6 character code
(ex: EB1772) that can be found both on the unit’s package
and on the reverse side of the unit. To enroll a transmitter,
provide central station (either by telephone or by fax) of the
Transmitter ID.
2.2 Initial Test
Upon pressing the transmit button, the Base Unit will sound
and display simultaneously a message of calling for help.
This
indicates that the transmitter is working properly.
Note:
If for any reason the MCT-212
AMBER
does not result
in the above response from the Base Unit, please contact the
central station and verify the Transmitter ID located both on
the unit's package and on the reverse side of the transmitter
beneath the wrist band
.
3. GENERAL COMMENTS
Product Limitations
Our wireless systems are very reliable and are tested to high
standards. However, due to their low transmitting power
(required by FCC, DTI and other regulatory authorities) there
are some limitations to be considered:
A.
Receivers may be blocked by radio signals occurring on or
near their operating frequencies, regardless of the code
selected.
B.
A receiver can only respond to one transmitted signal at a
time.
C.
Wireless equipment should be tested regularly (at least
once a week) to determine if there are sources of
interference and to protect against faults.
4. SPECIFICATIONS
Frequency (MHz):
315, 433.92, 868 or other frequency
according to local requirements.
Transmitter ID:
Over 16 million possible code combinations.
Minimum Transmit Duration:
2 sec
Power Supply:
3-volt Lithium cell type CR-2032
Battery Life Expectancy:
3 years (for typical use)
Battery Supervision:
Good battery - LED lights steadily upon activation.
Low battery - LED flashes upon activation.
Note:
If transmission is still possible despite the battery
condition, the MCT-212
AMBER
will send a low battery report to
the receiver.
Operating Temperature:
0° to 50°C (32° to 122°F).
Dimensions:
39 x 37 x 13 mm (1-9/16 x 1-7/16 x 5/8 in.).
Weight:
25 g (0.9 oz).
Color:
Gray
This device complies with Part 15 of the FCC Rules and RSS-
210 of Industry and Science Canada. Operation is subject to
the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
WARNING:
Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.
