DE3633 DISCOVERY QUAD MCW Installation Instructions
1
DISCOVERY QUAD MCW
Wireless PowerCode Quad PIR Detector
Installation Instructions
1. FEATURES
Employs a real quad element low-noise pyroelectric sensor
Includes a fully supervised PowerCode transmitter
Patented sophisticated motion analysis algorithm - True Motion
Recognition (TMR™)
Two-position vertical adjustment for coverage pattern
Integral swivel bracket for wall or ceiling installation
Programmable motion event counter - ON or OFF (default)
Front and back tamper switches for improved tamper protection
Full stabilization achieved 30 seconds after power up
After detection, the detector disables itself to save battery
power. It reverts to the ready state if there is no subsequent
detection throughout the following 2-minute period
Automatic termination of
walk-test after 15 minutes
Low current consumption
Microprocessor-controlled
temperature compensation
Sealed chamber protects the
optical system
White light protection
Elegantly styled, sturdy case
Keyhole-shaped slot for easy
removal of PCB
Figure 1.
External View
2. SPECIFICATIONS
OPTICAL
Detector Type:
Quad element low-noise pyroelectric sensor.
Detection Pattern:
90° wide angle lens with 19 quad zones in 3
detection
layers.
Max. coverage is 15 x 15 m (50 x 50 ft).
Adjustment:
2-position vertical adjustment scale: FAR and NEAR.
Figure 2.
Coverage Pattern
ELECTRICAL
Internal Battery:
3
V Lithium battery, Panasonic CR-2 or
equivalent
Nominal Battery Capacity:
750 mAh
Standby Current Drain:
0.015 mA
Transmit Current Drain:
20 mA (including LED)
Battery Life Expectancy:
3 years (for typical use)
Battery Supervision:
Automatic reporting of battery status with
each alarm and with periodic supervision message.
FUNCTIONAL
True Motion Event Verification:
2 position selector - 1 (OFF) or
2 (ON) motion events.
Alarm Period:
3 seconds.
Visual Indications:
LED lights
for about 3 seconds upon transmission of alarm &
tamper messages and upon each motion detection in the walk
test mode.
LED flashes
during the power-up stabilization period, or after
restoring (pressing) the tamper switch.
LED does not light
upon transmission of supervision messages.
Rearm Timer:
Rearms the detector 2 minutes after the last alarm.
Timer disabled in the walk test mode.
WIRELESS
Frequency (MHz):
315, 433.92, 868.95, 869.2625 or other
frequencies according to local requirements.
Transmission Sequence:
3 data bursts at variable intervals
within 3 seconds.
Encoding:
24-bit ID, over 16 million possible combinations.
Total Message Length:
36 bits.
Tamper Alert:
Reported when a tamper event occurs and in any
subsequent message, until the tamper switch is restored.
Supervision Message:
Once per 15 minutes, 60 minutes or
according to local standards.
MOUNTING
Height
:
With bracket :
Up to 3.6 m (12 ft)
Without bracket:
2 - 2.6 m (6.5 - 8.5 ft)
Installation Options
:
With bracket:
Surface or ceiling
Without bracket:
Surface or corner
Bracket Adjustment
: 20° downward, 20° left and right.
ENVIRONMENTAL
RFI Protection:
>30 V/m up to 1000 MHz.
Operating Temperatures:
-10°C to 50°C (14°F to 122°F).
Storage Temperatures:
-20°C to 60°C (-4°F to 140°F).
Compliance with Standards:
Designed to comply with FCC Part
15 and Directive 1999/5/EC of the European Parliament.
PHYSICAL
Dimensions (H x W x D):
117 x 65 x 47 mm.
(4-5/8 x 2-9/16 x 1-7/8 in.).
Weight:
92
g
(3.25 oz) without bracket, 107
g (3.75
oz) with bracket.
Color:
White
PATENTS:
U.S. Patent No. 5,693,943