manualshive.com logo in svg

Vislink ADVENT DCU5000, Operation Handbook

Share
Download
Vislink ADVENT DCU5000 Operation Handbook Download Page 17

Advent Communications 

209297 – DCU5000 Drive Control Unit 

Page 17 of 42 

 

4.26.  F25: MRD POWER FAILED 

The MRD power supply is out of specification. Either the supply has been shorted on 
the antenna, or an internal DCU5000 supply rail has failed. 

4.27.  F26: INCLINOMETER POWER FAILED 

The inclinometer power supply is out of specification. Either the supply has been 
shorted on the antenna, or an internal DCU5000 supply rail has failed. 

4.28.  F27: FPGA WATCHDOG TRIGGERED  

The hardware watchdog in the FPGA has timed out. All motor drive and brake outputs 
are disabled. The system will not be able to be driven. Power cycling the DCU5000 will 
reset the FPGA watchdog. 

This alarm is triggered by a serious software timing error which should never 
occur. If seen, please report the occurrence to Advent Communications 
customer support. 

4.29.  F28: GPS COMMS. FAILURE 

Serial communications with the GPS unit has been lost. 

4.30.  F29: COMPASS COMMS. FAILURE 

Serial communications with the compass unit has been lost. 

4.31.  F30: FEED DRIVE FAILURE 

The polarisation mode compensation feed drive has detected an illegal state. 

4.32.  F31: HHC OVERIDE ACTIVE 

An HHC option is not available with the DCU5000. This alarm should never be 
triggered, if seen please report the occurrence to Advent Communications customer 
support. 

4.33.  F33: FIN 1 OVER TEMPERATURE 

The measured temperature of heatsink fin 1 has exceeded 90°C. The operating 
temperature of the unit is out of specification, the unit side ventilation grills are blocked, 
or the units cooling fan have failed. 

4.34.  F34: FIN 2 OVER TEMPERATURE 

The measured temperature of heatsink fin 2 has exceeded 90°C. The operating 
temperature of the unit is out of specification, the unit side ventilation grills are blocked, 
or the units cooling fan have failed. 

4.35.  F35: FIN 3 OVER TEMPERATURE 

The measured temperature of heatsink fin 3 has exceeded 90°C. The operating 
temperature of the unit is out of specification, the unit side ventilation grills are blocked, 
or the units cooling fan have failed. 

4.36.  F36: FIN 4 OVER TEMPERATURE 

The DCU5000 does not have a heatsink fin 4. This alarm should never be triggered, if 
seen please report the occurrence to Advent Communications customer support. 

4.37.  F37: FIN 5 OVER TEMPERATURE 

The DCU5000 does not have a heatsink fin 5. This alarm should never be triggered, if 
seen please report the occurrence to Advent Communications customer support. 

4.38.  F38: WGS POWER SUPPLY ALARM 

The waveguide switch power supply is out of specification. Either the supply has been 
shorted on the antenna, or an internal DCU5000 supply rail has failed. 

Summary of Contents for ADVENT DCU5000











































Reviews:

No comments

Brands by name

Popular brands

Load more brands