Vislink ADVENT DCU5000 Operation Handbook Download Page 15

Page: 15 / 42

Advent Communications

209297 – DCU5000 Drive Control Unit

Page 15 of 42

4.8.

F7: FREEWHEEL DETECTED

A drive axis freewheel has been detected. It is possible that a freewheel on a drive
display can clear itself and this alarm shows the cause of the axis becoming
uncalibrated.

Possible causes:

Axis hitting physical end stop.

Moving antenna under high wind or snow loading.

This alarm is latched, and has to be cleared through the alarm clear menu option.

4.9.

F8: END OF TRAVEL DETECTED

A drive axis travel limit has been detected. The axis causing this will become
uncalibrated.

Possible causes:

Severe axis stall or freewheel causing the calculated angle which the soft stop
uses to be seriously in error.

4.10. F9: TX POL SWITCH FAILED

The TX polarisation switch, if fitted, has been detected in an illegal state or will not
respond to switch commands. Possible causes:

Manual operation of the switch with the DCU on will trigger this alarm.

Switch is disconnected.

Switch is stuck or jammed.

4.11. F10: AZIMUTH STOW SENSOR FAILED

The sensor used to detect the azimuth tab markers has failed. Possible causes:

Sensor disconnected.

Sensor failure.

Metal stuck in sensor.

4.12. F11: ELEVATION STOW SENSOR FAILED

The sensor used to detect the elevation tab markers has failed. Possible causes:

Sensor disconnected.

Sensor failure.

Metal stuck in sensor.

4.13. F12: POL STOW SENSOR FAILED

The sensor used to detect the polarisation markers has failed. Possible causes:

Sensor disconnected.

Sensor failure.

Metal stuck in sensor.

4.14. F13: EL DP SENSOR FAILED

Currently not used in the DCU5000 system. If seen please report the occurrence to
Advent Communications customer support.

4.15. F14: FA DP SENSOR FAILED

Currently not used in the DCU5000 system. If seen please report the occurrence to
Advent Communications customer support.

4.16. F15: EL STOWED SENSOR FAILED

Currently not used in the DCU5000 system. If seen please report the occurrence to
Advent Communications customer support.

Summary of Contents for ADVENT DCU5000











































Search results

Summary of Contents for ADVENT DCU5000

Reviews:

Related manuals for ADVENT DCU5000

Brands by name

Popular brands

Vislink ADVENT DCU5000, Operation Handbook

Search results

Summary of Contents for ADVENT DCU5000

Reviews:

Related manuals for ADVENT DCU5000

Brands by name

Popular brands