manualshive.com logo in svg

Vislink ADVENT DCU5000, Operation Handbook

Share
Download
Vislink ADVENT DCU5000 Operation Handbook Download Page 12

Advent Communications 

209297 – DCU5000 Drive Control Unit 

Page 12 of 42 

 

3.5. 

AZIMUTH, ELEVATION AND POLARISATION MOTOR CONNECTORS 

This interface is designed to directly drive an Advent standard stepper motor drive. 
These use 2-phase stepper motors with an MRD (motor rotation detector) PCB and an 
optional brake. 

Detailed descriptions are beyond the scope of this manual. Contact Advent 
Communications for further guidance and information. 

Connector: 15-pin male D-type. 

Pin Number 

Signal description 

1 

Motor phase +A. 

2 

Motor phase -A. 

9 

Motor phase +A. 

10 

Motor phase -A. 

 

 

3 

Motor phase +B. 

4 

Motor phase -B. 

11 

Motor phase +B. 

12 

Motor phase -B. 

 

 

5 

Brake active pull down. 

13 

Brake supply (+12V DC) 

 

 

6 

MRD +5V DC supply. 

7 MRD 

GND. 

14 MRD 

signal. 

15 MRD 

GND. 

 

 

8 

Motor presence detector 

 

 

Summary of Contents for ADVENT DCU5000











































Reviews:

No comments

Brands by name

Popular brands

Load more brands