www.visionsecurity.com.tw
Installation & Operation Manual
Product Description and Specification:
Introduction
Thanks for choosing the Vision’s wireless Arrival Sensor of
the home security device. This sensor is a Z-Wave™ PLUS
enabled device (interoperable, two-way RF mesh networking
technology) and is fully compatible with any Z-Wave™
enabled network and it’s security framework. Every mains powered
Z-Wave PLUS enabled device acts as a signal repeater and multiple
devices result in more possible transmission routes which helps eliminate
“RF dead-spots”
Z-Wave™ PLUS enabled devices displaying the Z-Wave™ PLUS logo can
also be used with it regardless of the manufacturer, and ours can also be
used in other manufacturer’s Z-Wave™ PLUS enabled networks. This
sensor assigns everyone with an unique ID then you could take care of
your family to send you any instant notification when they are coming
home or leaving home, also you could interact some specific scenarios
with specific persons When the device is secure included into Z-Wave
network, above communication will be encrypted. ARRIVAL SENSOR
supports SECURITY S0 / SECURITY S2 UNAUTHENTICATED /
SECURITY S2 AUTHENTICATED.
Limited Warranty
Vision Guarantees that every wireless Arrival Sensor is free from physical
defects in material and workmanship under normal use for one year from
the date of purchase. If the product proves defective during this one-year
warranty period, Vision will replace it free of charge. Vision does not issue
any refunds. This warranty is extended to the original end user purchase
only and is not transferable. This warranty does not apply to: (1) damage
to units caused by accident, dropping or abuse in handling, or any
negligent use; (2) units which have been subject to unauthorized repair,
taken apart, or otherwise modified; (3) units not used in accordance with
instruction; (4) damages exceeding the cost of the product; (5) transit
damage, initial installation costs, removal cost, or reinstallation cost. For
information on addtional devices, please visit us at
www.visionsecurity.com.tw
Federal Communications Commission Statement
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution
“the user that changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
the equipment.”
FCC Statement in User’s Manual (for calss B) FCC Section 15.105
“Federal Communications Commission (FCC) Statement”
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specification:
Package Content
Protocol: Z-Wave™ (ZM5101)
Frequency Range:
865.22MHz (ZA1501IN-5)
868.42MHz (ZA1501EU-5)
869.00MHz (ZA1501RU-5)
908.42MHz (ZA1501US-5)
916.00MHz (ZA1501IL-5)
919~923MHz (ZA1501KR-5)
919.80MHz (ZA1501HK-5)
922~926MHz (ZA1501JP-5)
921.42MHz (ZA1501BR-5)
Operating Range: Up to 100 feet line of sight
Operating Temp.: -10°C~ 60°C (14°F ~140°F)
1pc Arrival Sensor
1pc Micro USB Cable
1pc Operation Manual
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 60°C (5°F ~140°F)
Z-Wave Command Classes:
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_BATTERY
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_NOTIFICATION_V8
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_TRANSPORT_SERVICE_V2
COMMAND_CLASS_VERSION_V3
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Z-Wave S2 Support Command Classes :
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_BATTERY
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_NOTIFICATION_V8
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_VERSION_V3
COMMAND_CLASS_WAKE_UP_V2
Notification V8 Type:
TYPE
System (0x09)
Heartbeat (0x05)
Timer Ended (0x02)
Clock (0x0B)
(Table 1)
Notification Type
EVENT
V1 Alarm:
0x09
V1 Alarm Type
0x0B
VALUE
0xFF
0x00
TYPE
(Table 2)
1
Parameter 1
VALUE
1 ~ 255 (unsigned decimal) Seconds
(default: 2 (=16seconds x 2))
BYTE
Configuration Command Class:
(Table 3)
ZA1501-5 V0 1080227 6B1Z-15RS2
Arrival Sensor
ZA1501IN-5
ZA1501EU-5
ZA1501RU-5
ZA1501US-5
ZA1501IL-5
ZA1501KR-5
ZA1501HK-5
ZA1501JP-5
ZA1501BR-5
(P.S.: This is the definition how long ZA1501-5 will contact Gateway for
having a synchronic information. The basic interval time is 16 seconds,
the synchronic time will be the basic interval time by Parameter 1’s value.)
