manualshive.com logo in svg

VIRTINS VT RTA-168A/B, Manual

Share
Download
VIRTINS VT RTA-168A/B Manual Download Page 28

VT RTA-168A/B Manual Rev. 1.5 

 

www.virtins.com                                                             28                              Copyright © 2010-2020 Virtins Technology 
 

Virtins Technology 

 

 

Typical THD and THD+N Measurement 

 

 

 

Typical SMPTE IMD Measurement 

 
 

2.6 Multi-Instrument Software Specifications 

A complete Multi-Instrument software package consists of basic and add-on modules with all 
features  in  each  of  them.  The  basic  modules  include  Oscilloscope,  Spectrum  Analyzer, 
Signal Generator, Multimeter, Derived Data Point Viewer, Derived Data Curve, and General 
Functions.  The add-on modules include Spectrum 3D Plot, Data Logger, LCR Meter, Device 
Test Plan, Vibrometer, and Dedicated Hardware Support.  
 
There  are  six  license  levels  to  access  the  basic  modules:  Sound  Card  Oscilloscope,  Sound 
Card  Spectrum  Analyzer,  Sound  Card  Signal  Generator,  Multi-Instrument  Lite,  Multi-
Instrument Standard, and Multi-Instrument Pro.  The add-on modules need to be purchased 
separately.  They  can  only  run  with  Multi-Instrument  Lite,  Standard,  or  Pro,  except  that 
Vibrometer can only run with Multi-Instrument Standard or Pro.  The following table shows 

Summary of Contents for VT RTA-168A/B







































Reviews:

No comments

Brands by name

Popular brands

Load more brands