Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com
49401710A0 00 2105
46235.015B
Telecamera
Camera
Istruzioni per l’uso
Quick start guide
Dima di foratura
Drill template
Viti e tasselli
Screws and Plastic plug
Installazione scheda SD e collegamento dell’alimentazione
Installare la scheda di archiviazione:
1 - Allentare le viti di fissaggio del coperchio posteriore come illustrato di seguito
(Fig. 1).
2 - Inserire la scheda SD nello slot della scheda di archiviazione (Fig. 2).
3 - Rimontare e fissare il coperchio posteriore.
Installazione telecamera
Prima di iniziare, assicurarsi che la parete sia sufficientemente solida
per sopportare il peso della telecamera. Installare la telecamera
in ambiente asciutto. La procedura di montaggio è la seguente:
1- Passare i cavi attraverso la staffa. Montare la speed dome sulla staffa (Fig. 3).
2- Fissare la speed dome alla staffa con le viti (Fig. 4)
3- Utilizzare la dima di foratura per praticare i fori per le viti sulla parete (Fig. 5).
4- Allineare le due viti ai fori indicati dalle frecce e lasciare circa 12 mm dal muro
(Fig. 6)
5- Collegare i cavi e quindi appendere la staffa al muro e fissarla (Fig. 7-8).
Introduzione
Questa telecamera IP Speed Dome è stata progettata per fornire soluzioni TVCC
ad elevate prestazioni. Adotta chip di elaborazione video allo stato dell'arte. Utilizza
le tecnologie più avanzate di codifica e decodifica video ed è conforme al protocollo
TCP/IP, SoC (System on Chip) per assicurare la stabilità e l'affidabilità del sistema.
I manuali completi e i software CVM, Iptool.exe e Diskcalculator.exe sono disponi
-
bili nella scheda prodotto consultabile nel sito www.vimar.com
Connessioni
Di seguito sono riportate le principali connessioni della telecamera.
Introduction
This Speed Dome IP-camera is designed for high performance CCTV solutions. It
adopts state of the art video processing chips. It utilizes most advanced technolo
-
gies, such as video encoding and decoding technology, complies with theTCP/IP
protocol, SoC (System on chip), etc to ensure this system more stable and reliable.
Complete manuals and CVM, Iptool.exe e Diskcalculator.exe software are available
to download in the Product info sheet section of www.vimar.com website.
Connections
Here below the main connections of the camera
Install SD Card and Power Connection
Install Storage Card:
1 - Loosen the fixed screws of the rear as shown below (Fig. 1).
2 - Insert the SD card into the storage card slot (Fig. 2).
3 - Install back the cover back.
Camera Installation
Before start, please make sure that the wall is strong enough to withstand
the weight of the camera. Please install the camera in the dry environment. The
mounting steps are as follows:
1- Pull the cables through the bracket. Mount the speed dome to the bracket (Fig.
3).
2- Secure the speed dome to the bracket with the screws (Fig. 4).
3- Drill the screw holes on the wall according to the drill template (Fig. 5).
4- Drive the two screws to the holes indicated by the arrows and leave 12mm
clearance (Fig. 6).
5- Connect the cables and then hang the bracket on the wall and fix it (Fig. 7-8).
Overview
Installation
Cable
Connection
1
2
3
Networ
k
Cable
2
1
Quick
Start
Guide
HD PTZ
Camera
■
Please read this instruction carefully before using the product
and keep it for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without
notice.
►
Connecting
Network
Cable
1 Ethernet
connector
2
3 Safety
wire
Power connector
1
2
3
DC12V
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through the
both elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the
nut
and
the
main
cover
.
3
Micro
SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert
a
micro
SD
card
1
.
Loosen the four screws of
the cover and then remove
the cover.
2
.
Insert
a
micro SD
card as indicated
above and
then install
the cover
back
.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Overview
Installation
Cable
Connection
1
2
3
Networ
k
Cable
2
1
Quick
Start
Guide
HD PTZ
Camera
■
Please read this instruction carefully before using the product
and keep it for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without
notice.
►
Connecting
Network
Cable
1 Ethernet
connector
2
3 Safety
wire
Power connector
1
2
3
DC12V
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through the
both elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the
nut
and
the
main
cover
.
3
Micro
SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert
a
micro
SD
card
1
.
Loosen the four screws of
the cover and then remove
the cover.
2
.
Insert
a
micro SD
card as indicated
above and
then install
the cover
back
.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
1 Connettore Ethernet /
Ethernet Connector
2 Connettore di
alimentazione/ Power
Connector
3 Filo di sicurezza / Safety
wire
Overview
Installation
Cable
Connection
1
2
3
Networ
k
Cable
2
1
Quick
Start
Guide
HD PTZ
Camera
■
Please read this instruction carefully before using the product
and keep it for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without
notice.
►
Connecting
Network
Cable
1 Ethernet
connector
2
3 Safety
wire
Power connector
1
2
3
DC12V
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through the
both elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the
nut
and
the
main
cover
.
3
Micro
SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert
a
micro
SD
card
1
.
Loosen the four screws of
the cover and then remove
the cover.
2
.
Insert
a
micro SD
card as indicated
above and
then install
the cover
back
.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Package
Overview
Installation
1
2
3
4
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through the
both elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
E
thernet
connector
.
Then
tighten
the
nut
and
the
main
cover
.
Warning
and
Caution
■
If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■
Do not allow water or liquid intrusion into the camera.
■
In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■
Do
not
use
camera
beyond
specified
voltage
range
.
■
Do not drop the camera or subject it to physical shock.
■
The grounding hole of the product is recommended to be
grounded to further enhance the reliability of the camera.
■
Avoid touching the camera lens.
■
If cleaning is necessary, please use clean cloth to wipe it gently.
■
Do not aim the camera at the sun or extra bright place.
■
Do not place the camera in extremely hot, cold, dusty or damp
locations, and do not expose it to high electromagnetic radiation.
■
To avoid heat accumulation, good ventilation is required for
operating environment.
Quick
Start
Guide
Panoramic Bullet
Network
Camera
Camera
Quick
start
guide
CD
Plastic
plug
×4
Drill
template
Screwdriver
Rubber
plug
4 tapping screws
●
Connecting Alarm Input/Output
■
Please read this instruction carefully before using the product
and keep it for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without
notice.
2
1
3
1
Ethernet Connector *
2
Audio Input (MIC)
3
Audio
Output (HP)
4
Alarm Input/Output
5
RS485
6
Power
Connector *
7 Ground
8
Reset
9
Micro SD Card Slot
*
1
*
2 This camera can be powered by DC 12V/PoE power supply. If
the
PoE switch
is
used
to
power the
camera, DC12V
power supply
is
not
required
.
It
is
recommended
to
install
the
security
cap
for
outdoor installation
.
Se
cu
rit
y c
ap
Gr
ou
nd
1
3
4
5
6
7
8 9
2
A
LA
RM
4 3 2 1
R 4
85
S
+
A
LA
RM
4 3 2 1
R
4
85
S
+
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
RS485T-
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera.
①
Open the cover of the camera and then insert a micro SD card.
Then install back this cover and fix it firmly with the screws (please
keep it flat when installing).
●
Connecting
Network
Cable
Alarm
Power Source
IPC
ALARM-COM
ALARM-OPEN
Alarm Input
Alarm Output
+
+
-
-
Sensor
IPC
ALARM-INA
ALARM-GND
3
4
1
2
Overview
Installation
Cable
Connection
1
2
3
Networ
k
Cable
2
1
Quick
Start
Guide
HD PTZ
Camera
■
Please read this instruction carefully before using the product
and keep it for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without
notice.
►
Connecting
Network
Cable
1 Ethernet
connector
2
3 Safety
wire
Power connector
1
2
3
DC12V
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through the
both elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the
nut
and
the
main
cover
.
3
Micro
SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert
a
micro
SD
card
1
.
Loosen the four screws of
the cover and then remove
the cover.
2
.
Insert
a
micro SD
card as indicated
above and
then install
the cover
back
.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
Telecamera Speed Dome IP 2Mpx (1920 × 1080), sensore CMOS 1/2,8in, obiettivo
5 ~ 75 mm, filtro IR meccanico, zoom ottico 15x, illuminatori IR con portata fino a
150m, slot SD CARD 256GB, funzioni di analisi video, WDR, BLC, Defog e 3DNR,
RTSP, alimentazione PoE+ (IEEE 802.3at) o 12 Vdc max 22 W, completa di staffa
da parete, grado di protezione IP66. Dimensioni senza staffa ø 173x247 mm. Peso
2100 g.
Speed Dome IP 2Mpx camera (1920 × 1080), 1/2.8in CMOS sensor, 5~75 mm
lens, mechanical IR filter, 15x optical zoom, IR illuminators with a capacity of up
to 150m, 256GB SD CARD slots, video analysis functions, WDR, BLC, Defog and
3DNR, RTSP, PoE+ power supply (IEEE 802.3at) or 12 Vdc max 22 W, complete
with wall bracket, IP66 protection degree. Dimensions without bracket ø 173x247
mm. Weight 2100 g.
Contenuto della confezione
Una volta ricevuto il dispositivo, controllare gli accessori indicati di seguito. Le illu
-
strazioni sotto riportate hanno solo funzione di riferimento. Far riferimento all'appa
-
recchiatura in dotazione.
Package content
After you receive your device, please check the following accessories. The pictures
here are for reference only.
Overview
Installation
Cable
Connection
1
2
3
Networ
k
Cable
2
1
Quick
Start
Guide
HD PTZ
Camera
■
Please read this instruction carefully before using the product
and keep it for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without
notice.
►
Connecting
Network
Cable
1 Ethernet
connector
2
3 Safety
wire
Power connector
1
2
3
DC12V
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through the
both elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the
nut
and
the
main
cover
.
3
Micro
SD Card Installation
Please make sure the wall is strong enough to bear the dome
camera’s weigh and the camera is powered off during
installation.
This PTZ camera supports wall or ceiling mounting. Please select
a way to install as needed. The following instructions are for
reference only.
Insert
a
micro
SD
card
1
.
Loosen the four screws of
the cover and then remove
the cover.
2
.
Insert
a
micro SD
card as indicated
above and
then install
the cover
back
.
Wall Mounting
1. Pull the cables through the
bracket.
3. Drill the screw holes on the wall
according to the drill template. Then
insert the plastic plugs into the holes.
4. Insert two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
5. Connect the cables and then
hang the bracket on the wall.
6. Attach the bracket to the wall
with four screws.
2. Secure the PTZ camera to the
bracket with screws.
12
