Viale Vicenza 14
36063 Marostica VI - Italy
www.vimar.com
03982 01 2007
03982
IoT electronic control device for 1 roller shutter with slat orientation and
change-over relay output for cos
φ
0.6 motor 2 A 100-240 V~ 50/60 Hz,
2 inputs for external push buttons to control the roller shutter actuator,
favourite position recall function, remote control, double IoT technolo-
gy on Bluetooth 5.0 standard for the creation of VIEW Wireless mesh
system and on Zigbee 3.0 standard, 100-240 V 50/60 Hz power supply,
flush-mounting (retrofit).
The retrofit device for roller shutters is designed to control the roller shutter/slat through
the push buttons connected to inputs P
and P
and via a wireless connection. The
device has the possibility of being controlled with two different radio standards (exclusive
to one another): Bluetooth mesh (default) or Zigbee (which can be set via the VIEW
Wireless App). The Bluetooth mesh network implies the presence of gateway 20597-
19597-16497-14597 while for the dialogue via Zigbee a Zigbee coordinator
is required
(such as Amazon Echo Plus, Echo Show or Echo Studio).
It is equipped with an output with 2 one-position stable relays with interlocked operation,
in other words with mutually exclusive activation of the relays with a minimum interlock-
ing time. In the event of a mains power supply failure, the relays both remain open. The
push buttons connected to inputs P
and P
only control the roller shutter actuator
on board:
- Short press: if the roller shutter is not moving, the slat rotates; if the roller shutter is
moving, it stops.
- Long press: the push button connected to P
raises the roller shutter whereas the one
connected to P
lowers it.
- Double pressing of either of the two push buttons: recalling of favourite position (this is
saved via the VIEW Wireless App).
FEATURES.
• Rated supply voltage: 100-240 V~, 50/60 Hz.
• Dissipated power: 0.55 W
• RF transmission power: < 100 mW (20 dBm)
• Frequency range: 2400-2483.5 MHz
• Terminals:
- 2 terminals (L and N) for line and neutral
- 2 terminals (
and
) for the roller shutter output
- 2 terminals (P
and P
) for the connection of the push buttons for the actuator
control and for configuration. For the actuator control, use push buttons art. 20066-
19066-16121-14066 or art. 20062-19062-16150-14062 whereas
for configuration
use only push buttons art. 20066-19066-16121-14066
.
• RGB LED that indicates the configuration status (flashing blue).
• In Bluetooth technology mode, you can associate up to 2 EnOcean devices (art.
03925) which make it possible to control the actuator or activate a scenario.
• Operating temperature: -10 ÷ +40 °C (indoor).
• Protection degree: IP20.
• Configuration from VIEW Wireless App for Bluetooth technology system and Amazon
App for Zigbee technology.
• Controllable via VIEW App (for Bluetooth technology) and Amazon Alexa (for Zigbee
technology).
CONTROLLABLE LOADS.
Maximum loads
Roller shutter motor
100 V~
2 A cos ø 0.6
240 V~
2 A cos ø 0.6
OPERATION IN Bluetooth technology MODE.
The device operates by default in Bluetooth technology mode and this standard makes
it possible to:
- associate the radio control 03925 which can be configured to control the actuator
on-board or to recall a scenario;
- control the QUID system devices.
Through the use of gateway 20597-19597-16497-14597 the functions can be managed
locally or remotely via the VIEW App, and the control is also available via the voice assis-
tants Alexa, Google Assistant and Siri.
The device is also compatible with Homekit.
Settings.
The VIEW Wireless App can be used to set the following parameters:
- Actuator: with or without slat (default: with slat).
- Roller shutter activation time (default: 60 s).
- Slat rotation time (default: 2 s).
- Favourite position saving (default: 50% roller shutter, 0% slats i.e. open).
- Scenario activation delay time (default: 0 s).
- Compatibility with QUID roller shutter/dead-man (default: not active).
Reset procedure
To perform the reset and return the device to its factory settings, during the first 5 min-
utes that the device is powered, press for 30 s both push buttons connected to P
and
P
until the white LED flashes.
CONFIGURATION.
For configuration operations on the system in Bluetooth technology mode please
see the instruction manual for the VIEW Wireless App.
OPERATION IN Zigbee technology MODE.
For operation in Zigbee technology mode, the device should be associated with the
Amazon voice assistant which supports this standard, for instance Amazon Echo Plus,
Echo Show or Echo Studio; the following parameters can then be set on the push but-
tons connected to P
and P
:
- Selection between roller shutter or roller slat (default roller slat).
- Roller shutter activation time (default: 60 s)
- Total slat rotation time (default 2 s)
For the device to be associated with Amazon Echo Plus, Echo Show or Echo Studio, it
needs to be converted from Bluetooth to Zigbee using the VIEW Wireless App, then set
it to pairing mode and subsequently follow the procedure provided by the voice assistant.
The Amazon Alexa App will signal this procedure is complete accompanied by three
green flashes of the device LED.
Pairing mode activation.
• Immediately after conversion to Zigbee technology (or the software update), the device
will automatically go into pairing mode so that it can be recognised by the Amazon
device within 5 minutes.
• If the device is not in pairing mode, you can start this setting by cutting off the power
supply to the device and restoring it after a few seconds.
• Pairing mode lasts 5 minutes, after which it is automatically disabled.
Manual sequence for parameter setting.
1)
During the first 5 minutes after the device has been powered (already associated with
Alexa) or within 5 minutes from association with the ZigBee device, press for 15 s both
push buttons connected to P
and P
; this way, you will enter the activation time
settings phase (the LED flashes green during the roller shutter closing, which will take
180 s or until the push button connected to P
is pressed). At this stage the LED
is lit in green permanently and for 2 minutes pending the pressing of the push button
connected to P
; then press the push button connected to P
for a prolonged time
to raise the roller shutter. During the raising process the LED flashes green and to stop
it briefly press the push button connected to P
. The time that passes between the
long press and the short press is the roller shutter raising time, which will be saved by
the device as the handling time (the LED lights up amber).
2)
At this stage the total slat rotation time configuration begins. Press the push button
connected to P
and the roller shutter begins to close; during this phase the LED
flashes amber; when the roller shutter is closed the LED remains lit in amber perma-
nently and each short press of the push button connected to P
increases by 200 ms
the slat rotation time and each press of the push button connected to P
decreases
it by 200 ms. Each press will turn the amber LED off and back on again and will move
the slats.
3)
Press the push buttons connected to P
and P
simultaneously to store the desired
rotation time and the LED will flash amber quickly three times.
N.B.
If at the beginning of the slat handling time configuration the button is not pressed
shortly and the confirmation is given immediately by pressing both buttons at the same
time, the slats will be excluded from operation. So in practice, when the roller shutter
is in motion, pressing a button briefly will stop it whereas if the roller shutter is not in
motion pressing the button briefly will not give rise to any movement.
INSTALLATION RULES.
• Installation and configuration must be carried out by qualified persons in compliance
with the current regulations regarding the installation of electrical equipment in the
country where the products are installed.
• The relay output power circuit must be protected against overloads by installing a
device, fuse or automatic 1-way switch, with a rated current not exceeding 10 A.
• Installation must be carried out with the system switched off.
REGULATORY COMPLIANCE.
RED Directive. RoHS directive.
Standards EN 60669-2-1, EN 301 489-17, EN 300 328, EN 62479, EN 50581.
