Application Drawing
Vi22001U Single Port 90W PoE Midspan Installation Manual
IP Camera-end Installation
The Smart Choice for Transmission Solutions
www.vigitron.com
Important Safety Warning
- Connect the UTP Cables (Cat5/6) from the IP camera or other PoE
powered device to the “Data + PoE” RJ45 connector of Vi22001U. The
cable must be a Cat5/6 with a maximum length of 100m (328 feet).
Ethernet Switch/NVR-end Installation
- Connect the UTP Cable (cat5/6) from the Ethernet switch to the “Data”
RJ45 connector of Vi22001U. The total length of UTP cable from network
switch to the powered PoE device should not exceed 100m (328 feet).
- Plug the AC power cord provided with the unit to the mains.
- Read these instructions. Keep these instructions. Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer’s instructions.
- This installation should be made by a qualified service person and should
conform to all local codes.
- DO NOT bundle UTP signal wires in the same conduit as high-voltage wiring.
- To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron
equipment.
- DO NOT install the unit in a place where the operating ambient
temperature exceeds 60°C.
- Make sure that the power source voltage is in the recommended range.
- Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus that produce heat.
- Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long
periods of time.
- Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as a power
supply cord or plug is damaged, liquid has been spilled, or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
- The mains plug is used as the disconnect device and shall remain readily
operable.
WARNING! - To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture. This apparatus shall not be exposed to
dripping or splashing and no objects filled with liquids, such as vases shall
be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must
be connected to a mains socket outlet through an AC to DC Power supply
when using DC input.
WARNING! - The mains plug is used as the disconnect device and
shall remain readily operable.
The MaxiiPower Model
Vi22001U is a unique Single port PoE Midspan
designed for the most demanding power applications of 10/100/1000
Base-T networks. With the ability to provide up to 90W PoE power, it is the
most cost effective method for powering PTZ domes cameras with heaters
and blowers. The Midspan is compliant IEEE 802.3af, at, bt calss 0-8 and
UPoE standards for up to 90W PoE applications.
The Vi22001U can virtually meet requirements of any high power PoE
application. Its unique internal control system enables it to handle both
single PD and dual PD PoE devices.
The Midspan is equipped with LEDs to provide power status. No IP setting
or configurations are required and it can completely transparent to the
Ethernet network and higher layer protocols.
The Vi22001U is smaller, lighter and easier to fit in environmental
enclosures than most single channel power supplies.
Vi22001U_UM
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Max
ii
Power
TM
Powering High power PoE devices at Extended Distances
Powering PoE devices at standard and Extended Distances
Vi22001U
Coax
Cat 5/6
Network Switch
Vi22001U
Vi22001U
Vi22001U
IP Camera
IP Phone
Data +
PoE
IP Cameras
Vi3005
Hi PoE PTZ Dome
60W IR/
LED Light
Data +
90W PoE
328 ft. (100m)
Vi22001U
Data +
90W PoE
328 ft. (100m)
Data +
90W PoE
Data
328 ft. (100m)
Data +
90W PoE
328 ft. (100m)
328 ft. (100m)
Data +
PoE
328 ft. (100m)
Data +
90W PoE
328 ft. (100m)
The Vi22001U can be used to provide power to a wide variety high PoE power PoE powered
devices with Single or Dual PDs.
Network Switch
Vi22001U
Vi2301A
Vi2301A
IP Camera
Data +
90W PoE
328 ft. (100m)
The Vi22001U can be used along with extenders to provide power to PoE powered devices
at long distances.
Data
Data
Data
