Application Drawing
Vi2400A Ethernet Extender over Coax Installation Manual
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
IP Camera-end Installation
The Smart Choice for Transmission Solutions
www.vigitron.com
The MaxiiCopper Mini Model Vi2400A is a very compact data transmission
device that extends full-duplex High-Speed Ethernet over existing coax
infrastructures. It extends 10BaseT signals up to 5,000 ft (1,524m) and
100BaseT up to 1,800 ft (548m). It can fit in most camera housings and
junction boxes. With Pass Through PoE (PTP™), it can handle up to 30W
PoE power. It employs
MaxiiCopper
™
innovative and unique Ethernet
extension technology that is designed to take full advantage of
high-bandwidth networking cables and maintain a full-duplex 10 or 100Mb/s
Ethernet connection up to the maximum range with minimum transmission
error and latency. Vi2400A can connect multiple remote network devices
such as Mega-pixel IP cameras or VoIP to a central LAN switching fabric
with ease. Its automatic dual-rate capability feature balances the best
possible network throughput and long-reach distance.
The Vi2400A is a transmitter device and needs to be deployed on the
camera end. The data rate between the remote and central locations is
automatically set based on the distance. It is equipped with LEDs to provide
link status and configured data rate. No IP setting or configurations are
required and it is completely transparent to the corporate IP network and
higher layer protocols. The Coax cable needs to be point to point without
any branches and multiple segments can be joined together using barrel
connectors.
Ethernet Extenders
Important Safety Warning
- Connect the IP camera RJ45 connector to the 10/100BaseT Ethernet port
of Vi2400A using a standard Cat5/6 cable of maximum 100 m in length.
- Connect one end of the long coax cable to the BNC connector of
Vi2400A.
The link LED on the 10/100 connector should be “ON” to indicate proper
connection between the camera and Vi2400A.
Ethernet Switch/NVR-end Installation
- Use a Vi2401A/Vi2404A/Vi2408A or Vi2416A on the receiving side.
- If using a Vi2401A set the Master/Slave dip switch to “Slave” mode and
Set the Remote/Local switch to Local.
- Connect the RJ45 connector of the Ethernet switch to the 10/100BaseT
Ethernet port of Vi2401A using a standard Cat5/6 cable of maximum
100 m in length.
- Connect one end of the long coax cable to the BNC connector of Vi24xxA.
The link LED on the 10/100 Ethernet connector should be “ON” to indicate
proper connection between the switch and Vi24xxA. Also the Traffic LED
on the Coax side should be on and flashing to indicate proper connection.
While the Link LED, Orange for 100BaseT and Green for 10BaseT, in a
steady state will indicate confirmed connection between extenders.
IP Camera
Up to 5,000 ft.
(1,515 m) Coax
Cat-5
Cat-5
Data
NVR
Network Switch
Vi2400A
Vi2401A
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer’s instructions.
- This installation should be made by a qualified service person and should
conform to all local codes.
- DO NOT bundle UTP or Coax signals in the same conduit as high-voltage
wiring.
- To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron
equipment.
- DO NOT install the unit in a place where the operating ambient tempera
ture exceeds 75°C.
- Make sure that the external power supply output voltage is in the recom
mended range.
- Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including DVRs) that produce heat.
- Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long
periods of time.
- Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as a power
supply cord or plug is damaged, liquid has been spilled, or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
- The mains plug is used as the disconnect device and shall remain readily
operable.
WARNING! - To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture. This apparatus shall not be exposed to
dripping or splashing and no objects filled with liquids, such as vases shall
be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must
be connected to a mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and
shall remain readily operable.
Eth
ern
et &
P
oE
E
xte
nd
er o
ver C
oax
Vi2400
TM
Made
in U
.S
.A.
Po
we
r
