manualshive.com logo in svg

Vigilantplant TDLS8000, User Manual

Share
Download
Vigilantplant TDLS8000 User Manual Download Page 20

 

 

<1.  Overview>

1-3

IM 11Y01D01-01EN

1.2 

Name and Function of Each Part

TDLS8000 is composed Laser Unit and Sensor Control Unit.

n

  TDLS8000 case

External earth terminal

Cover

Lock screw (*1)

Display window

Nameplate

*1: 

Close the cover securely and fix it with a lock screw. Loosen the lock screw before opening the cover.

NOTE

Do not lose the lock screw when loosening it.

n

  TDLS8000 laser unit

LU display

Displays transmission.

Earth terminal for shield wires

LU fuse

Connecting terminal

Jumper for the overvoltage 

protection element

Usually leave it intact. (*1)

*1: 

The TDLS8000 is equipped with an overvoltage protection element to prevent failure caused by surges and other overvoltages. 

This element may hinder the correct measurement of the insulation resistance of the power line during insulation tests. To disable 

this element, disconnect the jumper.

3rd Edition: Jun. 10, 2016-00

Summary of Contents for TDLS8000

































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands