Viessmann Vitotronic 200 KO1B Operating Instructions For The System User Download Page 18

Page: 18 / 52

Setting the time program efficiently

If you would like to set a different time program for just
one day of the week, proceed as follows:

Example: You want to set a different time program for
Monday:
1. Select the period

"Monday–Sunday"

and set the

time program.

Heating time program

Monday

Saturday-Sunday

Monday-Friday

Monday-Sunday

HC1

Select with

(

Fig. 11

Note

The tick is always set at the sections of the week
with identical time phases.
Factory setting: Same for all days of the week,
therefore

"Monday-Sunday"

is ticked.

2. Then select

"Monday"

and adjust the time program

for that day.

Note

The

"Saturday-Sunday"

part of the week is ticked

because the set time phases correspond only to this
part of the week.

Heating time program

Monday

Saturday-Sunday

Monday-Friday

Monday-Sunday

HC1

Select with

(

Fig. 12

Deleting time phases

■

Set the time for the end point to the same time that
was set for the start point.
Or

■

For the start point, select a time prior to 00:00 h.

The display shows the selected time phase as
"

- - : - -

Operation

Time program

(cont.)

5592667

Summary of Contents for Vitotronic 200 KO1B





















































Search results

Summary of Contents for Vitotronic 200 KO1B

Reviews:

Related manuals for Vitotronic 200 KO1B

Brands by name

Popular brands

Viessmann Vitotronic 200 KO1B, Operating Instructions For The System User

Search results

Summary of Contents for Vitotronic 200 KO1B

Reviews:

Related manuals for Vitotronic 200 KO1B

Brands by name

Popular brands