manualshive.com logo in svg

Viessmann VITOCONTROL-S, WB2B, Service Instructions Manual, Page: 73 / 124

Share
Download
Viessmann VITOCONTROL-S, WB2B Service Instructions Manual Download Page 73

73

4.

d

Scanning is completed.

Fault codes

Fault
code on
the dis-
play

Const.

weath.-
comp.

System char-
acteristics

Cause

Measures

0F

X

X

Control mode

Maintenance  Service the equip-

ment. After the
service, set coding
address "24:0"

10

X

Controls as if
the outside
temperature
were 0 

°

C

Short circuit,
outside tem-
perature sen-
sor 

Check the outside
temperature sen-
sor (see
page 83)

18

X

Controls as if
the outside
temperature
were 0 

°

C

Break, out-
side tempera-
ture sensor 

Check the outside
temperature sen-
sor (see
page 83)

20

X

Regulates with-
out flow tem-
perature sen-
sor (low loss
header)

Short circuit -
system flow
temperature
sensor 

Check the low loss
header sensor (see
page 85)

28

X

Regulates with-
out flow tem-
perature sen-
sor (low loss
header)

Break, sys-
tem flow tem-
perature sen-
sor 

Check the low loss
header sensor (see
page 85)

30

X

X

Burner blocked Short circuit,

boiler water
temperature
sensor 

Check the boiler
water temperature
sensor (see
page 85)

38

X

X

Burner blocked Boiler water

temperature
sensor lead
broken 

Check the boiler
water temperature
sensor (see
page 85)

Troubleshooting

Fault display

 (cont.)

5692 760 GB

Summary of Contents for VITOCONTROL-S, WB2B





























































































































Reviews:

No comments