manualshive.com logo in svg

Viessmann VITOCONTROL-S, WB2B, Service Instructions Manual, Page: 44 / 124

Share
Download
Viessmann VITOCONTROL-S, WB2B Service Instructions Manual Download Page 44

44

Coding in the delivered condition

Possible change

0d:0

Function "Emergency
mode in case of insuffi-
cient system pressure"
disabled

0d:1

Function "Emergency
mode in case of insufficient
system pressure" enabled.
Minimum system pressure,
see page 8.
The burner starts with the
lower output.
The fault message "A2" will
be displayed (see
page 75) as long as the
system operates in emer-
gency mode.

0E:0

System pressure below
maximum value.

0E:1

Max. system pressure
exceeded during opera-
tion. Fault message "A4" is
displayed as long as the
max. system pressure is
exceeded.
For the max. permissible
operating pressure, see
the boiler type plate.
After the fault has been
removed, reset the coding
address manually to 0.

Note
The value is set automati-
cally.

 

11:

≠

9

No access to the coding
addresses for the param-
eters of the combustion
controller

11:9

Access open to the coding
addresses for the parame-
ters of the combustion con-
troller

21:0

No maintenance interval
(operating hours) selec-
ted

21:1
to
21:100

The number of hours run
before the burner should
be serviced is adjustable
from 100 to 10,000 h
1 step 

≙

 100 h

23:0

No time interval for
burner service selected

23:1
to
23:24

Interval adjustable from 1
to 24 months

Codes

Code 2

 (cont.)

5692 760 GB

Summary of Contents for VITOCONTROL-S, WB2B





























































































































Reviews:

No comments